Hey if you guys are into Chevy and GM inline 6s in general I have a group just for you. We have active discussions, knowlegeable members and polls to...
The World Village Computer Revolution Knowledge is power, Internet is money, 1 village 2 computers plan . Dear friends: This is 1 US dollar Internet education...
Fwd: The world public enemy. TSANG Yam-kuen, Hong Kong Chief Executive Dear friends: Help! Hong Kong Police using Brain Voice Read-Write Machine kill the Hong...
I have a 1965 GMC. I am going to replace the 350 tranny with a 700r4. This is 2 inches longer than the 350 and will require that I cut the drive shaft down....
best bet is to have the drive shaft cut down, cheaper, and a lot less labor paulwittenb <emusic@...> wrote: I have a 1965 GMC. I am going to replace...
yes i have cut several drive shaft the trick is to cut with portaband leave 1/6 crack for weld to fill tack on four corners when done roll it on very flat...
frank45cortez@... Wrote: Yes, I have done the same. well I moved motor foward that was more better a lot better, shorter fan adpter no big thing move...
i use to have a 84 c10 4x4 pick up i replaced the 305 with an 400 small block it had that 700 r in that trans has 7 gears of drive whats good for hot roddin is...
... From: classic60schevytrucks@yahoogroups.com [mailto:classic60schevytrucks@yahoogroups.com]On Behalf Of th c Sent: Sunday, December 18, 2005 10:22 AM To:...
Well now that everyone has had a chance to give input , I thought I would give mine. Yes the driveshaft is the easiest way and the least time, but think about...
So you can put the newer73-85 type mounts in just by drilling new holes ? thanks Tom truc5454 <no_reply@yahoogroups.com> wrote: Well now that everyone has...
Yes, the mounts work great! Now I am not sure about the 1960-1962 torsion bar set up , but I do know that my 1963 and my sons 1965 had no problem. As for...
I have I 66 short stepside that all I did was find a driveshaft out of a early 70s nova and it fit just fine. I also used a 77 nova trans crosmember which...
I think that Cliff's question is 'Was there an answer in there about moving the engine or cutting the drive shaft'? Where is the correct emoticon for this? ......
You are correct sir! I was thoroughly baffled ;) Cliff Daniel Truck Web Site http://members.cox.net/cwdaniel/ ... From: classic60schevytrucks@yahoogroups.com ...
I don't want to but it's one of those necessity things... I need something smaller with better mileage as a daily driver for work and I just do not have the...
http://pg.photos.yahoo.com/ph/tornadofilmsllc/my_photos Lon Lon Christopher Teter Tornado Films Park City, Kansas 67219 http://tornadofilms.8m.com aol im:...
Free magazines @ http://www.freshersonline.com/forums/ ... Yahoo! Photos – Showcase holiday pictures in hardcover Photo Books. You design it and we’ll...
We wish to invite members of your car club to an evening clinic on custom painting with Jon Kosmoski, founder of House of Kolor paints. Visit our Training page...
Richard, Since the members of this 'club' are spread around the world and communicate online, it would be difficult for us to make it to the South for the...
Hi all, Subscribe for job Alert: http://www.freshersonline.com/subscribe_job.html Freshers Job Saturday's(Jan 14) Nous Infosystems Recruit Freshers ...
Im looking for and axle rating for a 64 1/2 ton 4X4 front axle . How much weight will it carry? Also any one know the weight of the stock 292 six and 4 speed. ...
... I think the 292 + 4-speed weighs between 500 and 600 pounds. A half- ton axle won't really have any trouble carrying the extra weight, but the springs...
Yes its a detroit deisel 3/53 Im running 16" wheels and stock size tires. I was not so worryed about the torque on the axles but the stock transfer case . My...
... 4-low is plenty low enough to break stock 1/2-ton axle shafts - they just aren't very strong. The transfer case is really tough to break unless you put...
Well I tryed to bust a axle in the truck and tractor pull I entered it in 2004 . With the stock 292 and stock size tires . I was 4th place out of 8 trucks in...
Im going to try to look for a power steering box for my 64 4X4 k10 . any one know what box will be a close fit easy to get to work? Im thinking a chevy van or...
John Doe <bigbusguy@...> wrote: Im going to try to look for a power steering box for my 64 4X4 k10 . any one know what box will be a close fit easy to...
Thanks Il look there. But most places that sell truck parts only have stuff for 2 wheel drive. The 4X4 is not the same as the 2 wheel drive. I did not see any...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
