Hey, everybody, thank you for your thoughts and advice... I weighed the options and opted to have a trusted shop here in my small town replace the engine with...
Well, it has come to this. I recently had some kid reaerend my 66 longbed and i havent the heart or time anymore to redo what i worked on last summer. the bed...
I have a 65 GMC shortbed and looking to move the gas tank to the back. Anyone have especially good or bad experience with any particular product? Thanks....
I'm trying to start my 64 327cid, it turns over but will not start & run.I've replaced the plugs w/the correct gap,replaced the points ,condenser& coil,and the...
Got Gas ? ... will not start & ... gap,replaced the ... for the past 1yr ... adjusted the ... the distibutor to ... of the ... HEI dist that could ... ...
What he said, gas? And how old is that gas? Is there water in it after a year? then, is there power to the coil while the engine turning over? Does that power...
Gramp's, There are several things that it could be. Yes the gas would be first on my list. If you want to try to save time and see (without taking tank out)...
If so then you might want to check out the new 6cylinderloversofamerica2. It's devoted entirely to inline engines. If you're interested you can go to ...
Whenever it's raining hard or really humid the truck either won't start OR starts but runs VERY rough. I've had this happen before w/ other vehicles and it ...
Tomorrow I'll be replacing the weatherstripping on teh passenger side of my '66. Any suggestions as to the best type of adhesive to use? Lon Lon Christopher...
Do a resistance check on your plug wires with an ohm meter and make sure they have good continuity. I had a similar problem at higher RPMS. Terry Lon Teter...
Lon, there are so many diff types of adhesives on the market today. I would suggest going down to your local auto paint supply and see what they have in stock....
Just finished mine pulled the bed and put a tank in I bought from American Classic. didnt even have to drill holes frame holes lined up perfect went perfect ...
HI, I HAVE A 1964 GMC, 230/35. 6 CYL, 3/4 TON, PICKUP AND I NEED THE HARDWARE FOR THE LEFT DOOR, AND THE ARM REST. WHERE DO I FIND THESE PARTS. I NEED BOTH ...
CHATOZORRA@...
May 26, 2005 12:48 am
1859
I have had sucess with www.lcmtruck.com. Their outside handle kits are 39.99 each and has all the hardware. The part number is 38-6001. The inside door handles...
Thanks to all on both of my Truck groups (6066 Chevy Truck & Classic 60's Chevy Trucks). I replaced the distributor cap yesterday. I didn't go with the ...
Greetings All, Have just complete re-wiring my Beast and decided to replace my steering column. Got one out of TX that was in better shape on the steering...
I am wanting to get a pair of rear cab mounting brackets that are mounted on the l & r side of the frame. I have the replaceable 3/4ton (motor mount style)and...
Hey Guys, Looking for a good transmission hump the short style that is part of the floor not the bolt in type. Mine has been chopped up by the previous owner....
Hey Guys, I have a sbc Pre-87 Edelbrock 2101 non egr intake, Holley 80457-2 600 cfm sq flange vaccuum secondary carburator, GM HEI non computer distributor...
I am Parting out my 1962 Chevy stepside. It is rusty, and is currently in San Diego. I have a running 307 engine. Let me know what you need, and I will see if...
I have a '64 Nova 3speed 194 6. Does anybody know if the pivot arms that connect the shift linkage to the trannys are unique to 3 speeds, trucks, passenger...
I have bought a 66 C10 that has factory AC & heater, however it is a basket case with all the parts in the bed. What progression of assembly do I use to get it...
I can't seem to find a good condition without the bottom rotted off for a 64-66 chevy truck. I'm willing to pay cash and i'm located on the central coast of...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
