Truck: 1966 Chevy C-10 Engine: 1975 GM 250 inline 6 Issue: The truck had been running really rough so I took off the air cleaner assembly to check/adjust teh...
frank45cortez@... WROTE: HEY IT SEEMS TO HAVE A STUCK FLOOAT IS PROBELY WHY HUMM ? Truck: 1966 Chevy C-10 Engine: 1975 GM 250 inline 6 Issue: The truck...
I have 2 65' GMC shortbeds. They each have a 350/350 combo in them, but I would like to put in a 700r4 into the one that I am rebuilding. I'd like to know...
Cross member, relocate mounting holes Possibly driveshaft and/or yoke changes Shift linkage Elect connection for the Torque converter if it has the lock up. ...
So, here's the deal... My 1966 Chevy C-10 running a 1975 Chevy 250 inline 6 has lost all compression in #2 and #3 cylinders. Although I tend to always do my...
Lon, Any Chevy V8 or 6 from the mid sixtys on up will bolt directly into your truck. The biggest change will be your accelerator linkage, also be sure to get...
u may change it w a 350 ENG U WILL ONLY NEED NEW MOTOR MOUNTS BUT NOT THE SUPPORTS GOOD LUCK ... 1975 Chevy 250 ... cylinders. Although I ... replacing an...
Hey, everybody, thank you for your thoughts and advice... I weighed the options and opted to have a trusted shop here in my small town replace the engine with...
Well, it has come to this. I recently had some kid reaerend my 66 longbed and i havent the heart or time anymore to redo what i worked on last summer. the bed...
I have a 65 GMC shortbed and looking to move the gas tank to the back. Anyone have especially good or bad experience with any particular product? Thanks....
I'm trying to start my 64 327cid, it turns over but will not start & run.I've replaced the plugs w/the correct gap,replaced the points ,condenser& coil,and the...
Got Gas ? ... will not start & ... gap,replaced the ... for the past 1yr ... adjusted the ... the distibutor to ... of the ... HEI dist that could ... ...
What he said, gas? And how old is that gas? Is there water in it after a year? then, is there power to the coil while the engine turning over? Does that power...
Gramp's, There are several things that it could be. Yes the gas would be first on my list. If you want to try to save time and see (without taking tank out)...
If so then you might want to check out the new 6cylinderloversofamerica2. It's devoted entirely to inline engines. If you're interested you can go to ...
Whenever it's raining hard or really humid the truck either won't start OR starts but runs VERY rough. I've had this happen before w/ other vehicles and it ...
Tomorrow I'll be replacing the weatherstripping on teh passenger side of my '66. Any suggestions as to the best type of adhesive to use? Lon Lon Christopher...
Do a resistance check on your plug wires with an ohm meter and make sure they have good continuity. I had a similar problem at higher RPMS. Terry Lon Teter...
Lon, there are so many diff types of adhesives on the market today. I would suggest going down to your local auto paint supply and see what they have in stock....
Just finished mine pulled the bed and put a tank in I bought from American Classic. didnt even have to drill holes frame holes lined up perfect went perfect ...
HI, I HAVE A 1964 GMC, 230/35. 6 CYL, 3/4 TON, PICKUP AND I NEED THE HARDWARE FOR THE LEFT DOOR, AND THE ARM REST. WHERE DO I FIND THESE PARTS. I NEED BOTH ...
CHATOZORRA@...
May 26, 2005 12:48 am
1859
I have had sucess with www.lcmtruck.com. Their outside handle kits are 39.99 each and has all the hardware. The part number is 38-6001. The inside door handles...
Thanks to all on both of my Truck groups (6066 Chevy Truck & Classic 60's Chevy Trucks). I replaced the distributor cap yesterday. I didn't go with the ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
