Yea, I though I may run into several problems. I believe the truck may have around a 4:10 ??? but it is not a positive track. Is there a simple kit that can be...
Has any one dealt with this company recently? I am thinking of ordering some parts from them and was wondering if their merchandise was of good quality for...
i put a rear end out of a 76 trans am in my 63 it was about 1" narrower on each side, i had to make sure the bed was set right and then have about 3/4" clear...
I never heard of them,but I'm sure there are a lot of good companies that are available. One that I know of that has good products is www.impalas.com despite...
when i put a 76 trans am rear in my 63 i cut the mounts off the stock rear and welded them on the new rear so it would mount up no problem. the drive shaft had...
the 8.5 10 bolt gm rear is got to be stronger then the old 12 bolt rears because i have tore 3 of them up beond repair but i have not tore the 10 bolt out yet...
blonde_rn6 <no_reply@yahoogroups.com> wrote:Has any one dealt with this company recently? I am thinking of ordering some parts from them and was wondering if...
Robert, I had my rearaxle redone at a cost of 800.00. It was a 4.11 and a single track. I now have 3.42 with a P-track. The gears are resonable but the P-track...
Thanks for the advise. truc5454 <no_reply@yahoogroups.com> wrote: Robert, I had my rearaxle redone at a cost of 800.00. It was a 4.11 and a single track. I now...
Otis, I have never changed a rear end before. When you say, " cut the Mounts off " which Mounts ? the spring mounts ? otis stubbs <odie35501@...> wrote: ...
No clutches in the rear is the best way to go - clutches wear out, especially if you push it hard. That's why I went with locking rearends, but they're not...
... I have 4.10:1 gears in both of my trucks, but I run 33" and 35" tires. 4.10:1 is kinda low for tires that aren't so big. 3.37:1 is a good ratio. The...
Some of my favorite parts sources: chevyduty.com, americanclassic.com, LMCtruck.com, gspp.com, boyceequipment.com, jcwhitney.com If you need to re-wire, the...
Hey there, I bought REZ's engineering power steering kit ofr 60 bucks. Am completely happy with it and the quality of the stuff they sell. I have also used:...
I just pulled the 283 in my 65 apart to rebuild it and noticed that it has been rebuilt sometime in the past, bored 30 over and the crank has has been turned...
I have a 65 chevy 1/2ton 4x4 pickup. My dad has a 64 chevy 3/4 ton 4x4 pickup, both have the original transfer cases, yet my 65 has a different transfer case...
... that ... crank ... my ... safely ... later ... input ... shuold ... Most of the machine shops that bore the cylinders would be able to tell you if you...
The most common pistons are .020,.030,.040, and .060. You can get just about anything you desire with a special order. You can safely bore this block .040, or...
... I have heard of people even boreing a 283 out to be a 327 (increasing the bore from 3.875 to 4.00 = .125 over)[you also have to change the crank] but the...
I have a 65 chevy 4x4 pickup with a smashed drivers side front fender. The front of it with the headlight cup thing is broken off and smashed up. To fix it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
