Hi All, A while back I said I just got a 66 with 327,auto and in dash air.Well the snow melted enough to get through the permafrost and I finally towed it off...
Hi again, After getting the truck home,I started going over it.The trans is a Powerglide.It has the original cloth interior.Still in good shape.Question-Is...
anyway to tell if I got a broken ring without tearing the engine down? 1 cylinder has 10 pound compression that does not come up with oil squirted in.....also...
Here are some pictures of the 1963 Chevy Stepside I unfortunately must sell. I've added an album called Selling 63 Stepside. I anyone has any questions please...
I had some pics taken of the truck-under Bob's 66. This is my starting point.Everything is original.Tree sap on one side.lol Actual mileage is 93,750. Any...
Due to financial reasons we must sell our 1966 Chevy carryall. We live in southern missouri . if anyone is interested please email me at grayjrms@......
Hi all I am replacing old fuel lines full of bad gas,and I had a question.Since this engine was designed to run leaded gas,what do most of you run now?Do you...
66 Chevy pickup C10 project; Long bed fleetside, 250 6 cyl. 3 speed with Hurst floor shift. Runs, needs brakes. Some rust. Comes with extra parts including new...
Hi All I got the truck started yesterday after it had been sitting foir 4 years.Motor sounded good.Carb is a mess of course.I'm changing fuel lines today.One...
HI! Just joined this group. Found it through the moneypit site. I have a '64 that I'm putting back together and one day maybe I'll even get to drive it :)) I...
... we got a brand new one off e-bay for $157.00 It's works great and is perfect. It has the auto tranny spot that attaches to the bottom of it, 3 row and...
I have found an early 60's chevy truck that has the tachometer, and volt gauges in it,where there normally a design in the cluster, is this rare? If so, what...
... and ... A tach and an air pressure meter [air brakes] were common on C-30+ trucks, however the tach was offered as an option in C-10's. Up until about six...
... is ... I've seen a few of them on ebay for about $90 and up. Not exactly rare but not common either. Really depends on the shape of the gauges and needles....
... tachometer, ... cluster, ... gauges ... My 65 K10 has the factory tach in it. the guy i bought the truck from also bought the same panel for his other...
Hello out there I am looking for chromes for a 1963 chevy truck there are only two pieces one driver side an pasenger side. open door on rear of cab...
I have a rear end for my 66 fleetside, i noticed that it is narrower than my stock rear end, has anyone put one in their truck, was there any problems with...
Hello Everyone I'm new to the group and have question about a 66 C10 that i just got. My frame is ate up with rust, but have a 74 frame. Will this frame work...
Hey there Jon, No the frame will not work. You will have to change cab mounts, radiator support mounts and a whole slew of other things to fit the older body...
I am looking to replace the current rear end out of my 65 with a 373 positive track that came out of a 74 z-28. Is this possible and what problems should I...
... 373 ... what ... I doubt that even a Z-28 rearend is as strong as a standard truck rearend. Also, I doubt that it's as wide, so the spring pads may not be...
Yea, I though I may run into several problems. I believe the truck may have around a 4:10 ??? but it is not a positive track. Is there a simple kit that can be...
Has any one dealt with this company recently? I am thinking of ordering some parts from them and was wondering if their merchandise was of good quality for...
i put a rear end out of a 76 trans am in my 63 it was about 1" narrower on each side, i had to make sure the bed was set right and then have about 3/4" clear...
I never heard of them,but I'm sure there are a lot of good companies that are available. One that I know of that has good products is www.impalas.com despite...
when i put a 76 trans am rear in my 63 i cut the mounts off the stock rear and welded them on the new rear so it would mount up no problem. the drive shaft had...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
