Hi WhenI tune individual cylinders, right hand cyl wont rev clean. If I close the choke almost completely, then tune cylinder, it will rev out better, but...
Check the fuel flow from the tank to the carb. Sounds like too little fuel or you have an air leak somewhere between the choke and cylinder. If you are real...
Peter, The same situation happend to me when I was using the plastic gas filters on my Chang. With the filter placement being close to the engine, it melted...
Thanks for the replys. Tried the spray bottle of fuel around intake and carb, but no change in idle. I have spare carbs changed them and still runs breathless...
valve clearance OK,going to shorten fuel line so its pointing down, maybe better flow?Interesting ,when i use retard lever on left cyl,it has noticable effect,...
No it's not normal. Mine effects both cylinders. Is your bike a M1 22hp 6v? How is your compression? If they check OK, then I would replace the condensor,...
my OHV engine has developed a serious oil leak, about a quart every hundred miles. It seems to be coming from up high and from under the front engine cover. it...
Just bought a used M1M, and I'm in need of some spokes for the wheels. Does anyone know where I might buy short and long spokes at a good price. I did find...
I'm in need of some spokes for my M1M. I've found some stainless steel, U.S. made ones, but at $110 per set, they are out of my price range. Anyone know...
Greetings Mr. Shooting, Not long ago John Heim (Chang Jiang US) one of Dan's sponsors was advertising spoke sets that featured correct inside and outside...
Hey there everybody, I have an OHV charging question or two I'd like to run by the group. I searched first for any past posts on the OHV alternator and...
Thanks for input. I raised needle on lean side and it helps even things out, also havnt had time to look at timing but still starts easy. Due to lack of use Im...
This is my first time asking any questions.......Thank you I have a M1M 12 volt w/ side car and after the long winter here in Michigan The clutch seems to be...
Hi, DIsconnect the clutch cable and see if the clutch is still engaged. If yes then you need to check if the clutch actuating parts are not stuck and pevent...
Meet biker babes and biker dudes in your area and keep in touch with them in our community. Our social net-work service includes blog, forums, web mail,...
Meet hot biker babes and biker dudes here and keep in touch with them in our community. Our social net-work service includes blog, forums, web mail, groups,...
I have a CJ750 with approx 1400km on the clock. Shifting from 4th down to 3rd it seems to regularly undershift and jumps out on the top side. A small tap...
I too have a similar problem. Mine pops out of gear downshifting from 3rd to 2nd. It always happens when I'm turning a corner - very annoying. If I find out...
My problem is the opposite, 3rd to 4th., when I pore on the throtle she'll pop out of gear. Related or not--- problem seemed to fix itself after adding about ...
Hello all, First post here, I've found this place very usefull, so I decided to join, I don't know if I can contribute, but I will try to help if it's possible...
Hi, Did you rmove the screw holding the muffler ? To remove the shaft that hold the drive to the frame you need to remove that screw amd take a punch and a...
Hello Gerald, Thanks for your quick response :) Yes, I removed the screw and the muffler, and I tried to move the shaft using your method but not lucky (maybe...
Hi, The shaft might be frozen in it because of no maintenance like greasing it often. Use strength and put WD 40 by the hole for the grease fitting. Will...
Has anyone ever run across an OHV motor making a ticking noise from the points housing? The noise changes with motor rpm. I took the points plate off, and...
Hey Joe, I checked on Dan's site under toolbox (Dariusz Wiecha's Boyer ignition installation). There is a pinned joint in the distributor shaft. You'll need to...