I've found my old strobe timing light. Does anyone know the dynamic timing at ?rpm for an OHV engine. I've set it static but it would be nice if I could set...
Thanks to you all and welcome in board. Let's build this shop manual together. Soon I'll post in the file section documents regarding valves gap adjustment,...
Thanks again Gerald, I have a note book that I have been filling with what ever information I can find, ths will be a great help. Even small details are...
Hi guys, Sorry, I can't contribute much, since I don't have my CJ (OHV) yet, but I am confident this will change during the next month or so. I collected a few...
Hi guys, Here the numbers that I stole off the web. NOTE: all should valid for the OHV engine, but I have no idea if that numbers work for SV too (or are...
Sorry, the maintenance schedule came up warped. In my email it looks good though... Will try to correct it later... maybe with a file attached or so... No time...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cjmechanicalhelp group. File :...
cjmechanicalhelp@yaho...
Mar 16, 2005 8:03 pm
13
Hi All , I attempted to post 2 pdf files but they froze up yahoo, I wil try another format on sat. I posted a carb file in pictures but it is empty,...
I am going to send files to this group soon. I'll send them with power point and/or microsoft office. So if you do not have it yet, please get it ! REGARDS ...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cjmechanicalhelp group. File : /CHANG...
cjmechanicalhelp@yaho...
Mar 19, 2005 12:33 pm
16
Hi, Just sent a file with often asked stuff. REGARDS GERALD...
Hi all, Regarding the tyre pressures given in this document, I had never heard of tyre pressure measured in "atmospheres" so I looked up my conversion tables...
Hi, This is where this group is fully interesting : We are able to share informations regarding the differences in measurements and make them understandable to...
Engine Depending on the model, the CJ750 motorcycle is equipped with either a twin- cylinder side valve "Flathead" engine, or an Over Head Valve (OHV),...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cjmechanicalhelp group. File :...
cjmechanicalhelp@yaho...
Mar 19, 2005 3:26 pm
21
CJ750 motorcycles require the correct running in procedure to ensure optimum performance and durability. It is well worth taking extra care during the...
Preparation before Start Gasoline filling Although the CJ750 can use low octane fuels (80 RON minimum), the motorcycle is tuned to operate with a minimum of...
Some of us don't use the metric system, how about some spec's in inches, lbs, gallons, ounces, PSI and so on. I sure I'm not the only one without metric feeler...
Hi everyone, I just added a parts diagram folder in the files folder. I have converted all 22 pages into a PDF file. I hope you find this useful. Fred Balanay...
does anyone know if this is to far out of norm. diameters = Rt cyl, 3 o'clock/9 o'clock position 3.056", 6/12 o'clock. 3.063, rim of cyl. 3.071 6/12 o'clock,...
Hi Mike, Generally speaking one would measure a cylinder in three or four spots on the X and Y axis. Usually a difference of more than .002 inch would indicate...
Thanks George, It is a float problem on the right carb, the float needle looks like a finish nail and thats on a brand new carb (r75 reproduction) . I did not...
Hello, I have a special tool in my kit for the square head bolts on my sidevalve. However, the rear end of the tool is round, so I can't use the troque wrench...
Hi, There is a Sata socket that would fit perfectly in the other end of the head tool you have. If your head tool is the original one, the other end is...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
