Hello, I'm looking to buy a 22 swing keel, with trailor and brake, pop top, in the eastern canada or usa, if you got one for sale please send me all the info...
I have a 1977 Chrysler 22 for sale. I live in Huntsville, AL .......It comes with a double axle trailer. two winch handles, a new main sail, used but very...
I will pass this to my friend, he was looking for one. But I have question, on my C26 I have some chips on gelcoat what I have to fix, so I am looking for some...
Henry J. Jakl
HJakl@...
Jul 28, 2003 3:07 pm
839
I'm sorry to do this to everybody but I've recently had some complaints about viruses with my name and e-mail address involved. I don't reall understand how...
... Chris and the others: I've had the same problem. Email with virus sent with my address, subject "Re: Honey" Don't open email from me, fwuest@..., ...
Frank Wuest
fwuest@...
Aug 5, 2003 4:12 am
841
main
main@...
Aug 13, 2003 4:04 am
842
I'm not sure if the group is still alive, but anyway: Just recently bought a Chrysler 22 sailboat. Tried to raise the mast using home made bridles - it doesn't...
ddnsvy
ddnsv@...
Aug 20, 2003 4:25 am
843
Hello! I'm not sure if this list is still active either. It would be good if someone who knows would send out the address where there is an active list. I...
You folks keep talking and publishing your findings, OK? I just acquired a C22 for a BSA Venture Crew near Toledo Ohio and I have yet to step the mast. Your...
There is also a new website but I cant find its address... ... From: Steve Milanoski [mailto:svmilanoski@...] Sent: Wednesday, August 20, 2003 11:18 AM ...
Peabody, Bruce V.
BPeabody@...
Aug 20, 2003 3:41 pm
846
I rigged a schedule 40 steel pipe with a 5/8 inch rod epoxeed into the end and a ring fitting on the other end for attachment of blocks and halyard. Saves...
Peabody, Bruce V.
BPeabody@...
Aug 20, 2003 3:47 pm
847
Thanks fo the description of your system. I think that my bridle attachment rings are located too high, it's about 3-4 inches higher then the mast base level....
ddnsvy
ddnsv@...
Aug 20, 2003 11:31 pm
848
I've raised my share of masts on 22 foot boats and I have never had that much trouble. Two people can do it easy, just by walking it up I have also read that...
mjastex
mjastex@...
Aug 21, 2003 7:27 pm
849
The Catalina is a toy compared to the Chrysler. ... From: mjastex [mailto:mjastex@...] Sent: Thursday, August 21, 2003 3:27 PM To:...
Peabody, Bruce V.
BPeabody@...
Aug 21, 2003 7:28 pm
850
As a new owner of a Chrysler 22, I would agree with the observation that this message board is not functioning very well. Where do we go to post on the "other...
I design then fabricate or have fabricated what I need. Or take it off another boat. ... From: Gordon Kimball [mailto:gkimball2@...] Sent: Thursday,...
Peabody, Bruce V.
BPeabody@...
Aug 21, 2003 10:32 pm
852
I try to arrange things for folks but between scouting and work I miss obligations. I will try to see if I can get one made for you. I made a special anti...
Peabody, Bruce V.
BPeabody@...
Aug 21, 2003 10:36 pm
853
I never used the jig either.... just put the base onto foot and walked it up with the backstay and shrouds attached. I used the forestay and/or the halyard to...
Steve, you may have this info by now, but the address for the followup group to this board is http://www.chryslersailors.com. There is a link to the Chrysler...
This is a Special Offer from CellSiCo Sun, LLC Marketing Division. To remove your from our mailing list, use the link at the bottom of this message. ... ...
SellSiCo Solar PV
0723pv@...
Aug 25, 2003 6:53 am
858
Is this the correct rig tension for a 1976 22 ??? lowers - 325 - 350 lbs uppers - 375 - 400 lbs fore - 425 - 450 lbs back - 425 - 450...
Have you started out with the settings in the factory rigging instructions? If not, in the section on tuning the rig, they suggest "The best criteria for...
I was doing what should have been a simple job to run a VHF cable and some new wires for my mast lights, when I found that there is a small section of foam in...
deathsdad@...
Sep 11, 2003 12:44 pm
863
dont tie them together, use high strength duct tape and create a taper so there is not significatn bulge and it is straight in line. then carefully pull...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
