1968 2 door imp is wnat i used Eric Murray <thebaron512@...> wrote: Which car's weather stripping will cut down to fit on a two door? Thanks SPONSORED...
Hi Lawrence, Thanks for the interest ive gotten a lot of emails about them today. I'm lookin for 500 CDN that's with very recent rubber, plus shipping which...
Hi Thommo, Hey man I'll send some pics soon I've gotten alot of emails so bare with me. I'm lookin for 500 CDN with very recent rubber, plus shipping which im...
I have a 1981 X-11 that has a badly weathered dash pad and just found a 1980 Citation IP that is in pretty good shape (some cracks in the corners and slight...
They will swap. Use the ductwork and electricals from your 81'. But you might notice that the 80' will only have a speaker grill in the center of the dash. You...
i got a few questions for you guys. if i put an 85 k-frame in my 81, can i just cut out the rear cross member and weld the 81 cross member in so i dont have to...
unfortunately, i do...i have just had alot of things going on lately, as i'm sure you do as well...and haven't figured out what i want to do with the car...i ...
Hey Scott, You could notch out a section of the rear cross member on the 85 K frame & it would still be stronger than the 81 cradle - re-enforcing the area you...
The strut mounts are interchangeable for the most part, You just have to make one of the holes in the Strut tower into a slot to get it to fit. About half the...
That's cool.... I knew there was something to do with making the hole bigger... I didn't realize it was that simpel... as long as the 81 mounts are in good...
I've decided to go ahead and do the cradle swap. It'll be a lot easier to do, plus then I can rebuild the cradle at my leasure, and still enjoy the convertible...
so you guys are saying that i can use the existing strut and spindle and it will mount on the lower ball joint on the lower control arm? and another question...
Sorry for the delay I work a lot. If you dont have an extra set do you have a mechanical drawing of the part? If you do I can give it to my dad he is a...
I was GONNA say you had too much time on your hands, but then I watched the whole thing myself... Jason ... From: "Eric Murray" <thebaron512@...> To:...
Well, last weekend I removed the 5 speed tranny, shifter, and cables from my 81 X-11. This weekends project was to remove the 4 speed and bad clutch, replace...
I'm sure I can help you out with the pedal assy. Also the 4 speed I have has no problems...it's just geared too low for driving to work daily (55 miles...
Hello, It will be another day or so till the pix get up and posted, sorry. Also due to an overwhelming request for these rims, which is normal, I just might...
Hello, It will be another day or so till the pix get up and posted, sorry. Also due to an overwhelming request for these rims, which is normal, I just might...
Hello, It will be another day or so till the pix get up and posted, sorry. Also due to an overwhelming request for these rims, which is normal, I just might...
sounds good...55 miles one way, that stinks...i only really use citation for cruisin...i'm not sure what rpm's i'm at on the highway,,,i'll have to look next ...
Ya, the 81 struts and spindles will fit the new K-frame, that's what I'm doing with my 3800 swap. I am going to beat in the corner of the fire wall and use the...
Yeah, reminds me of my 81, but at $2100 opening bid I would expect more. Dash is all cracked, windshield is busted, the drivers door lost a fight, and front...
Hey dude, where you been hiding? I've got to send you a picture of my exhaust pipe project, will try to get to it after work today. I have the back side header...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
