1 at Andys auto 1 at Coreys and 1 at Bakers all of them are in the same area. If you have time to come down here I will show you all of them. Let me know. ... ...
Will what parts are you looking for? I will see if there on the car still. ... long time now. It's about 2.5 hours from me. ... think ... London/Ontario ... ...
... engine side. Between the dogbone and the block. The metal piece that has 2 bolts to the block. thanks, jamey Any X-car with a 2.8 should have that....
You were doing just fine, until you said 1980 Citation LOL. The 82 and up Citations will use the Fiero REAR control arm bushings. You may want to ask Aaron...
Advance lists TRW 12610 8.39/ea/4 req Mcquay Norris FB410 $11.99 Not sure if partsamerica.com (Advance Auto parts site) ships to Canada, but I could order them...
Thanks will I checked Part Source out they have the part for me. for 15.00 Cnd each and Prothane bushings are 37.00 pair special order 2 wks. Thanks again ......
Well my Buick Regal GS 1990 has been very troublesome lately (running really rough). Had replaced the coil packs and that made a difference, so just replaced...
Eric, What engine do you have? If you have a camshaft signal DTC, it should be a 3.8-L. Lots of questions if it is. post as much info on engine, DTC numbers,...
yeah well, the problem is, that with '80 to '81 cradles, the bolt diameter is 10mm, not 14mm liek it is with '82 and later cradles.. so you have to get a ...
the only other option for the control arm bushings would be to drill larger holes and use the bolts from an 82 or later cradle.. BUT i didnt have an angled...
... should be a 3.8-L. Lots of questions if it is. post as much info on engine, DTC numbers, etc, Dwayne 3800 series I motor, but not sure what the DTC...
I can already tell you what the problem probably is. The 3800 NON Supercharged Series 1 engines are NOTORIOUS for loosing the camshaft sensor magnet off the...
To elaborate further: Loss of the magnet on the cam gear results in the camshaft position sensor failure code (even if a new sensor is installed). This forces...
Tyre's correct - as usual. Early 3.8's had large problems with the cam sensor magnet. Some would split, some would come out of the plastic retainer and end up...
Aaron I see you didn,t have too press the sleeves out from the control arm. The guy at the performance shop said they have too be pressed out I'm thinking he...
This is going to be a shock who lives in Ontario Canada. On the news yesterday are Drive clean program is under review 7 years older could be exempt from...
Installed Accel Coil packs and a new Control unit, plus new wires and plugs recently. Of course, every place seems to be jammed packed with cars in need of ...
... <chevy_x11@y...> ... older ... older ... 30.000 ... pulse ... Here in ohio all cars from 1979 to date have to get emission check, so all citations as of...
1985 and newer have to be E-tested all cars and trucks. 1998 and newer could be exempt. should no something end of the year. and their talking about every 6...
nooonoooo.. you don't want to remove the metal casing.. the poly bushings use the stock metal sleeve.. the poly slides inside it..the metal slevee i was...
Thats what I thought. I knew about 10mm size when I read your cradle swap. Wait until I talk to him. Thank-you ... bushings ... slevee i ... the one ... on ...
Still considering the several x-11s that people have offered me so far, but if you missed my request, here it is. I am located in Pittsburgh, PA. Please email...
Hey does anyone want to buy my Sub speaker box that is in my basement? it is sitting in my garage right now, but its been in my basement for over a almost 2...
I have a model car of a citation notchback that I never had time to build and its taking up room in my basement so if anyone wants it give me a holler and we...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
