I'd put it this way. You'll probably never get out of it what you put in to it, but if you like the truck and want to drive it, then decide what it is worth...
AL, Yep. I have decided to bring it home. Heck, I can buy a reman 258 for 1600 or so. I don't know why I should pay a shop over 2K just to swap the motor out. ...
I'm getting old or something, I don't want to slap a clutch on a trail anymore. I am in the middle of pitching the 727 for a 2wd 700r4 and a divorced np205 ...
You will need to run the wires down ro see how the winch was wired in. Then go from there. I would hook up some jumper cables directly to the winch, and jumper...
Brush guards are hard to find. They weren't too common. Maybe a post on the IFSJA web site might find you one. But as I said the factory ones will be hard to...
get a 4 speed from a jeep pickup, it will swap in. Dodge stuff will not, the full size jeep is not in anyway related to dodge (as far as swappable parts go)...
I may have a flexplate for you...what year, motor and trans? Mark W. dsshull <dsshull@...> wrote: Sorry to hear about the motor. As has been said, I...
Sounds like us when someone comes across a sweet rig that needs a little work.... "You know, it's junk. You don't want it. I'll take it off your hands for...
We have a 1973 360 with a turbo 400 behind it. Thanks, Darrell ... either a 360 ... away. Only God can make it great. Choose wisely; there's a test at the...
Mark, Ya, I felt a but put off. I am picking it up on Monday. Best, Bryant ... From: Mark Wilde To: cfsja@yahoogroups.com Sent: Saturday, March 01, 2008 10:58...
Darrell, About the 73 360 with the turbo 400 behind it. How much work is that to install in a j-10 wthat currently has a 258 four speed? I know I can take out...
sorry....mhwilde-at-yahoo.com Mark W. Mark Wilde <mhwilde@...> wrote: Yup, got one for you. Email me off-list and we can figure out how to get it to you....
In my case, I have a D20 transfer case. I took the whole assembly - motor, tranny, transfer case out of a '73 Wagoneer and dropped them into my '66 J2000...
sidewinder huh? there was a thread about these winches not to long back on Co4x4. they were fairly popular back in the 70s. dont recall the make right off...
I happen to have a 360 and TH400, from a 1983 Wagoneer. I understand the mileage is about 83,000. Bad news is they are now in CA (I actually bought the whole...
...You'll end up on the side of I-25 with a VERY unhappy spouse. Going SB on I-25, going up the hill south of Loveland up to the AT&T antenna, I was BARELY...
Yea, I learned that lesson on a Taurus I had...everything still worked, but the filter was so clogged the pump had to work extra hard and finally burnt out. ...
You were down on the right hand side of the sb lanes weren't you? Saw you there as we went flying by. Nice looking wag by the way. We would have stopped to ...
how hard it the pedal assemply? i want to put a stick in my GW and am one unsure of how hard it is to install a clutch and two dont know where to get one with...
That's why I'm keeping the pump I bought for a spare. It's a Howell TBI, so it's a separate pump. Easy to get to after you remove the spare tire. (from the...
Yup, that was us. The truck looks good at 20 feet. More than a "bit" of faded paint and rust on the roof and hood when you get up close. Yes, DEFINITELY better...
Sorry, I have a Howell TBI system on my truck, so there's a pre- filter in front of the pump and I have one just before the throttle body assembly. Also, from...
my front right passenger door had trouble opening, if you push the latch down when the door's open it doesn't have trouble but if its closed it's rather hard...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
