Do not forward virus warnings of any kind to CFSJA. Most of the time they are HOAXES. Even if they aren't, do not forward warnings to the list. If you want to...
cfsja@yahoogroups.com
Apr 1, 2007 9:01 am
67470
CFSJA Emailing List What, Rules, Who, Tips Updated 4/14/2003 ** Please SAVE THIS MESSAGE somewhere after you READ IT ** SUPPORT OUR TROOPS * Join 4-Wheelers...
cfsja@yahoogroups.com
Apr 1, 2007 9:01 am
67471
In a message dated 3/31/2007 11:38:41 P.M. Mountain Daylight Time, ethan@... writes: So I'm seeing Mark wants the chassis and maybe the cab. Jason...
Are you just looking for the title and vin number Mark? I only want the bed and the frame behind the cab... with our without the springs. I might be interested...
Yes and the dash with the VIN plate. I may be able to use other stuff too. I have a J-20 but it the title is in another state from a guy I don't have contact...
I'm thinking that Jason and I (and whoever else is brave enough) will drive over to Palisade and pick it up sometime after Easter. I have to justify my new...
Under the cab? The front part of the frame has to be the same width (motor mounts are the same), but does it change that quickly? Since the J truck cab is...
Well, I finally figured out that the axle shafts on my 74 are bent and this is causing my locker woes. Now I am on the hunt for some axles shafts for a rear...
Scott, I would think PullnSave, everytime I go looking for extra shafts I see alot of the off-centered ones there. They are pretty easy to pull once you have...
I may take a look today but the last 6 or 7 times I've been there they didn't have any QT waggies so I am not going to count on it. Its usually a waste of time...
Scott, I'll run up there around 1:00 and check it out for ya. it is just up Peoria from me. So it was the QT's that had the offset axles. I've seen them before...
Thanks for looking Matt. It would save me a trip. Im not sure if the offset axle came in any other rigs then the QT. Maybe someone else will know and post it....
Dude email me! _autokawkr@..._ (mailto:autokawkr@...) Bill ************************************** See what's free at http://www.aol.com. [Non-text...
autokawkr@...
Apr 2, 2007 5:47 pm
67487
IIRC the Dana 20 rigs had slight right offset, but not as much as QT rigs. I have one willing to tear down Scott. I see you are pressed for time and I would...
I've got a rear end sitting somewhere over @ Jason's in loveland. You're welcome to it, I dunno what ratio, but IIRC, it was a QT era truck. I also have the...
yeah not far at all, nice to hear from ya galan john walgren <walgren2002@...> wrote: hey wzrubicon you are just down the road from me i live in clifton ...
I am off of I-70 and elberta, if the weather is good, I will start transferring the axles this weekend. I would like to get this all done in the next three...
take a measurement of the frame, measure your crossmember, send the results and someone will be able to say one way or the other. DAMWEASEL@... wrote:...
i guess i should explain more. Its louder when i let off the gas at about 40mph. I just got new exhuast last year around this time. I run 88 octane fuel. my...
I don't have any motor to hook you up with unless it's a big block from california. Somebody abandoned an old motorhome behind my house with some 1ton axels,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
