... Mind Control ============ See if you have good mind control over your body. This is left brain, right brain stuff. This actually is true even though it may...
Hi Everyone! I need to have my 727 trans and NP 221 t-case rebuilt. Does anyone have any suggestions on where to take it? I cannot pull the trans myself so I...
Where are you located? Denver? Co Springs? Ft Collins? Someone in the area might be bribed into helping you. <g> BTW, which care do you have? They're usually...
Hi I have an 83 wag with a rebuilt engine and carb, sometimes when I turn it off it will diesel for a second. It doesn't do it all the time and when it does...
There is an anti-desiel solenoid on your carb (assuming you have a stock carb, it's a 2150). It's designed to turn on when you start the truck and hold the...
Has anyone converted their 229 from a vacuum switch to a manual lever or cable to engage the CAD and transfercase. If so how did you do it? Are all the vacuum...
yes [Non-text portions of this message have been removed]...
J10Project@...
Mar 1, 2004 8:36 pm
44802
While the vac system sucks (sorry <g>) because the lines can deteriorate, fall off, etc., the system is a good one when all put together. Your 229 doesn't have...
Where are you? greenplaid1 <Jscattaglia@...> wrote:Hi Everyone! I need to have my 727 trans and NP 221 t-case rebuilt. Does anyone have any suggestions on...
I have a 4350 on my 76. all the extras were removed. It used to diesel quite often and backfire when shut off . I started replacing ignition components and...
... I'd suggest Parker Transmission & Gear in... well... Parker, CO. :) Btw, you probably don't have a 228 or 229 depending on year of your GW. Michael...
I would suspect the carb needs some adjusting. If that doesnt work you could have the same problem that i had with wiring. but i got that figured out, and mine...
So io finally solved my wiring woes. I should kick myself in the ass for what was wrong. Wheni was younger i thought that i could clean up my wiring in the...
... Often this is the result of carbon deposits in the cylinder igniting the air/fuel mix. FSJ's have a few measures to prevent this from the factory. The TAC...
CFSJA Emailing List What, Rules, Who, Tips Updated 4/14/2003 ** Please SAVE THIS MESSAGE somewhere after you READ IT ** ... TABLE OF CONTENTS =================...
cfsja@yahoogroups.com
Mar 2, 2004 5:02 am
44810
Everbody check out their comps. One of the IFSJA guys got a virus laden email from Toby@.... Toby hope your seeing this! Bill Only in a Full Size Jeep ...
autokawkr@...
Mar 2, 2004 5:13 am
44811
Hari, I'm still lurking out here. I still have the CJ-8. Nobody wanted it more than me. Now I'm collecting the last few parts for my 4.0 liter with an ...
The latest slew of mass mailers SPOOF the "From" portion of the email (it searches the hard drive for legit addresses). So it could've come from anywhere....
Hey all, I'm looking for the front sheet metal (not the fenders or hood) for a Rhino Grille conversion on my 83. I have a grille and false vent covers etc. All...
I decided to try another master cylinder in the 715 today. Went to Carquest in Ft Collins (just south of Ft C 4x4) and talked to Tom, who has an M37 and is...
I don't think that there is a difference between a j10 and j20 frame. A 715 is definitely stronger. I saw on the IFSJA site that Matkins is now making...
Peter, from what I've found, I do believe you are correct. The springs and knuckles differed from the j10 to the J20, but frame was the same dimensions. An...
You should be able to mount the Rhino Grille on your vehicle now, with some minor modifications. You will have some un-needed screw mounts, and some gaps in...
... Yea, I keep forgetting AutoZone insists there was no Wagoneer in 1972, and why parts stores ask what type of carburator it has when I ask for something...
Resistance wire is used to drop the "running" voltage to the coil, You start at 12v then when in the "run" position, the stock coil runs about 9 volts or so. ...
Resistance wire tries to not go where you want it to. If you have some electrical current that you want somewhere, it tries to protest and not deliver it, and...
Maybe that would work if the bleeders had a tube attached to them that went at least as high as the Master Cylinder, otherwise the fluid would just run out and...
Exactly...this theory only works if you keep the master cylinder full. I used to do this all the time when I was working at a repair shop here, and while...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
