thanks guys for all the help.. i got to school yesterday and asked a friend of mine to help me track down the prob.. it ended up just being the temp selector.....
That's great. It's also simple enough that you can disconnect it once in a while while the three girls are riding with you. ;) Isn't it great when a fix costs...
HAHA !!!! JB ... John A. Barclay IV "The New Mexican" 81 Jeep CJ7 aka "ROCKEATER" See the Jeeps http://www.aaafamilysites.com/family/johnb/photoalbum.html...
and on my budget.. wait.. i dont have a budget... thats how little i make... we need to make a poor wheelers fund... main beneficiary ME.... lol guess ill...
Does anyone know about changing out a head light switch on a 76 cj5? mine is on the fritz and i'm going to get the new swtich today.. is it an easy fix? :) HB ...
Pull off the knob and unscrew the little retaining collar on the front of the switch. It will have 2 opposing notches for a spaner wrench, although a small...
Should be easy to do, first disconnect the battery, then reach under the dash and on the side of the switch there is a push pin push it in and pull the switch...
HAHA ! No kidding Dennis ! JB ... took longer to right this than to do the job!!!!!!!!! ... mine is on the fritz and i'm going to get the new swtich today.....
Yes, very easy. There is only one little tricky part and that's getting the knob off. If you hold the knob with one hand, then either underneath or on top of...
BTW when you say it's on the fritz, I had a problem with mine, tried replacing the switch a few times until I realized it was actually the dimmer switch on the...
Well, I haven't been on here in a while. I was in a motorcycle accident three weeks ago, and I have had to deal with a lot of problems that it caused (both to ...
sorry to here about your wreck, hope no one was injured to badly. If you have stock arms i have a spare set at the house if you need them, and as to the pinion...
Dennis also does a good job at reinforcing the control arms - mine look great!!! Sorry about all the pinion seal troubles :( Sorry about your accident!...
Hey blue hope you are recovering okay. AS dennis said you only got to remove the front end of the drive shaft from the yoke and then pull the yoke then the...
Haley are you still hualing scrap steel as i have about a full load. Dennis Anthony Haley <haleyanthony@...> wrote: Hey blue hope you are recovering...
Ok, this might be a dumb question, but after the four bolts are removed from the front, what do I need to do to detach the shaft? I tried pulling and pushing...
Should be able to push it back towards the t-case, and it shouldent take a lot of effort. if the slip yoke is stuck then that might be what is causing your...
I remove the 4 little bolts the stupid caps then stick a fair sized screw driver between the ujoint and and the pinion nut area. and pop it. if your front end...
x2 I always use a large screwdriver between the u-joint and the yoke. JP ... From the desk of J.P. Boileau Columbia, SC Mobile: 803-446-1330 Home/Fax:...
He's at Camp Lejeune and yeah, he's still my future SIL for now. Who knows what might happen when I actually lay eyes on it for the first time though.. :-) I...
David, Check out this website. The guy is local to me around Columbia: www.gr8tops.com Not sure if he'll be able to help, but it's worth a shot. JP ... From...
I am hoping to get a new front axle for my YJ and the new bolt pattern is 5 on 5.5. It is a Dana 44 out of a Waggy. I have the black rock crawler rims now...
If it is all there I think I can do an okay job getting it back together. Even if there is pieces missing I think we can make it usable. lets see some pics. ...
... Well, I have frame sliders on the bike, so no major mechanical damage. Dent in the gas tank, scratches on both sides, destroyed both rear view mirrors....
