The Holley 4180 is based in the 4160 design and is fairly similar in design however some mods were made to improve efficiency and fuel economy and it does have...
Hey thanks alot Bryan!, This is exactly what I was looking for. im gonna go through these links when I get more time. Bryan Purkey <brypur@...> wrote:...
Mathew, I have a couple of magagzine articles from the 80's that may be of help to you regarding modifying the 4180C from the mid 80's Mustang/Capri. If you...
Hey George, Yea. Id really appreciate that if you could scan them. You can send it to matthewt316@... or just posting them to the list if its possible...
Hi guys new to the group and got a problem. I have a 66 mustang that someone(previous owner) installed what appears to be a 83-85 CFI 302 with AOD tranny. now...
Welcome to the group. It has been slow so don't be shy. (Since I just approved you today I guess that means your not!) IIRC even the CFI ran the same fuel...
In my experience (limited) I have found that there are two types of in
tank pump EFI setups. I cannot tell you which you have, but hopefully
you can still use...
Anderson, Richard
randerson@...
Aug 7, 2006 12:23 pm
32004
Richard, What is the purpose of inserting *SPAM* in the subject line of your email? Thanks James ***************************...
Computer Service
computerservice@...
Aug 7, 2006 2:08 pm
32005
Sorry, it is done automatically by the new and improved email system
here. ________________________________
Richard Anderson
Senior Market Research...
Anderson, Richard
randerson@...
Aug 7, 2006 2:29 pm
32006
... the transfer pump outside of the tank should do the job. So i thank maybe some kind of restriction in the lines... what the previous owner did was plumb...
... Before you go off trying to solve the problem, first you must confirm what the problem is. Get yourself a fuel pressure gauge and plumb it in somewhere -...
A quick question, does this engine have stock intake, stock heads, and stock cam? If not, the load calculations controlling fuel mixture are probably fubar -...
wish i had a clue but i believe it is stock will check the EGR it does have a rough idle (not cam) it acts as if it is cold when i start it and wants to die ...
no rail to plumb to....this is CFI but will check the fuel psi!! ... Wade Pittman swpittman1@... "keep thy airspeed up, for the ground shall rise up and...
... I'm no cfi expert but I slept in a Holiday Inn Express once. *If* your EGR valve has any kind of feedback going to the ecm, it would be an "E"gr "V"alve...
An internal ERG valve vacuum leak can be the source of a nasty and seemingly impossible to cure rough idle. I chased a bad idle in a carbed Bronco II for years...
Hey anyone running the early 289 2v heads on late model 302? anyone got a carb reccomendation for my 5.0 with AOD tranny? Considering Converting on over to...
... don't ... carb ... !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! CAUTION I burned up tranys going carb/aod had to buy...
Uhm, I had a '84 t-bird parts car with a 302, CFI and an AOD old-school rod linkage. You don't need a cable system unless you want to spend money on something...
I'm not sure what the original poster wanted to know exactly about 289 heads. Stock for stock the 289 head will have a slight performance advantage over other ...
Alright i've had it with the CFI its outta here....now i have a alum high rise a edelbrock old style torker intake with the carb sitting kinda catty wampus...
I have done the same swap with those items you mention. I did the shaft but it was a pain as I had to weld on an extension on the trans end and hodge a ball on...
... Ya know, a Duraspark setup would be awfully cheap. Otherwise, you could scour the many Classifieds at Stangnet and Corral, perhaps even ebay (buyer...
The dura spark setup is quite good especially for the price. The down side to it is not being able to easily find one with a good timing curve. Most of these ...
If your a set it and leave it kinda guy then I guess that would work. I like to tinker and try to find optimum. At which point in time the MSD setup comes in ...
Does anyone know if there is available a manifold for the 302 block that
allows fitment of 4 Weber DCOE's. Below is a link to a picture for one
that fits a...
Anderson, Richard
randerson@...
Aug 24, 2006 4:37 pm
32024
Below is a link for one to fit the 302. http://www.webercarbsdirect.com/inc/pdetail?v=1&pid=7274 <http://www.webercarbsdirect.com/inc/pdetail?v=1&pid=7274> Tom...
Thanks and almost, but those are IDA's, not DCOE's. The IDA is a
vertical carb of similar design to the side draft DCOE. Unfortunately,
the IDA requires more...
Anderson, Richard
randerson@...
Aug 24, 2006 7:10 pm
32026
Try this link: http://www.webercarbsdirect.com/inc/pdetail?v=1&pid=7274 ... From: Anderson, Richard To: carbedMustang@yahoogroups.com Sent: Thursday, August...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
