Hey all, Now im trying to figure out why my spark plugs were all black and kinda oily. im thinking weak ignition.. So my question is has anyone heard anything...
I have never heard any compatibility problems with MSD Blaster coils and stock ignitions. MSD has a lot of coils, so make sure you pick the right one. They...
Anderson, Richard
randerson@...
Jul 6, 2006 12:13 pm
31969
I have a blaster on my 84 with the stock 5.0 and ignition....
Thanks Rich, Ill pass though. For now I just wanna get the coil. Does anyone on the list know if a 94 mustang cam is the same as the 87-93's? Im putting an 89...
Mattew go to Ebay and look for an explorer cam. These came in the 5.0 v8 explorers. They are known for being a high torque cam even more so than the stock HO...
I would think it would work well Matt. The 81 heads likely have large combustion chambers thus a low compression ratio. IMO it would be a good idea to find ...
Yea but Ive allready had the stock heads completly reworked. If I get board I might cc em and see. Thanks again man! John Stephenson <jdsgallops@...>...
Hey all, Well I took her for a fairly hard ride after work today. sounded good felt good with the new intake. When I would floor it it would surge then loose a...
I fired her up this morning before I had to head out and with the engine cold that smoke was gone. so maybe nothings wrong. Ill play with it more this week...
Where is the carb content on this Ralph???? Just wanted to drop a note to the list for the new members. We have had several sign up in the last few weeks. It...
Did some ask for carb content? http://images17.fotki.com/v323/photos/5/577697/3753916/06SAAC31VIR0468-v i.jpg If that doesn't get your heart beating faster,...
Anderson, Richard
randerson@...
Jul 19, 2006 4:07 pm
31980
save yourself some headaches and put the barry grant junk on e-bay and get a holley!! just my opinion, i could be wrong!! but probably not!! ... From:...
Low Carb? ... http://images17.fotki.com/v323/photos/5/577697/3753916/06SAAC31VIR0468 -v ... you ... Grant ... AN ... filter ... had ... so ... approved. My...
Joh takes away my bread... ... Uh, did you notice that there were TWO Shelby's? I'm pretty sure ONE of them has a carb. *grin* ... As I am just now finihsing...
... It sounds as if you have had a bad experience with BG carbs. ... I do not feel that you need anything more. Case in point are the EFI systems. I also run...
most evertone that has had one has had a bad experience!! LOL ... From: Puter ami To: carbedMustang@yahoogroups.com Sent: Thursday, July 20, 2006 10:06 PM ...
Has anyone removed the anti tamper caps on one of these, id so how did you do it. I have heard you drill a small hole formt he bottom. How far from the edge?...
Can everyone please elaborate on the bad experiences they have had with the Barry Grant Demon line of carbs. Not so much because I want to have a bash session...
Anderson, Richard
randerson@...
Jul 21, 2006 11:56 am
31987
Rich I don't know what Mike is eluding too but most of what I have heard is the jetting often being off. Something unusal for a "tuner carb". You might want to...
Been a few years but I just used a dremel to cut a slot along the bottom edge of the carb till I saw that I was past the plug. Then I used a small screwdriver ...
john, i have several personal friends and quite a few internet racer friends that have had really bad experiences with bg. both in workmanship and customer...
Their customer service is a misnomer. I have emailed three times with no response and spent at least two hours of my life on hold already. Plus, I have been...
Anderson, Richard
randerson@...
Jul 24, 2006 12:19 pm
31991
... I'm not sure you gave you that information but I think it is kinda funny. There are two reasons that plug reading has become a black art, EFI and dyno's....
Thanks John. That is a good link. Added to bookmarks. Around here, I through the local sports car club, I can get in a dyno day for $60/hr. At the prices...
Anderson, Richard
randerson@...
Jul 24, 2006 12:59 pm
31993
The problem with most dyno days is time. Since the group is there you are usually limited to a certain number of pulls. The prices I listed were for indivdual...
Interesting, my experience was the opposite. I have dyno with just one friend around and with a group and got a lot more done in terms of adjustments with the...
Anderson, Richard
randerson@...
Jul 24, 2006 1:55 pm
31995
On the subject of dyno tuning....for a carbureted car, with AFR, we charge $95.00 per hour. We have boxes of jets, metering plates, metering rods, air bleeds...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
