Cool. Nice installation. After talking to a few folks I think I'm going to mount mine in front of the spare tire well and behind the rear end, seems like it...
I plan to be at Beaver Springs Dragway on Saturday for their all day test & tune. Anyone else planning on being there? John (Stephenson?), I know you wanted...
I recently completed putting a 410 stroker in my 89 Mustang and now I seem to be having some driveability issues. The car idles fine, it revs fine, but when...
backfire thru carb is lean, backfire thru exhaust is rich. Ebok carbs are notorious for dislike of high fuel pressure, make sure you are at 5-6 psi at most. ...
I didn't have time to check the website, but I think that's correct. It's in Snyder County, PA, I think, unless it's in Union. It's not far off the US Rt....
Jeremy: This is John G. I have contacted you before wanting to meet you at BSD help tune your car. I am from York, PA. Unfortunately, I work 12 hour...
JpgStangs@...
Jun 16, 2005 11:04 am
31332
... Sounds like it. And very unique! If you can, take some pics and post as you go to work on this. Ralph...
... Nope I am down in FL. Little much of a drive but if you were closer I would be there. 95 Cobra/98 Explorer Tension and conflict are necessary ingredients...
Oops, got the wrong John. John G., I live about 15 minutes east of Ephrata on 322. I am hoping to rent BSD for several hours on July 16- not sure if it'll...
Hey all, Anyone got any 79-84 stang rubber body molding their willing to part with? If so please email me.. Matthew Southeastern AZ He that ruleth his spirit...
Ill check it out. Thanks Ralph ... Matthew Southeastern AZ He that ruleth his spirit is greater than he that taketh a city. Solomon, ... Life is not measured...
I set the floats to the specs on Edelbrocks website. They were a little off, but correcting them did not help. I did have some loose intake bolts, I tightened...
Jason, I have a feeling the popping sound is because your cam lobes got messes up somehow in your break-in of the motor. I had my comp cam in my 351w, the car...
The chances of getting a lobe wiped are slim. Possible but at this point I think it is a little premature to think that way. The symptoms he is describing are...
Oh no, John, not the Holley thing again :) I do still have my Holleys in the garage. The only problem with them is that they leak and need to be helicoiled....
Jason the key, I think, to your problem is the drive then coming to a stop and the slow death idle. Every time i have had this it is a car running too rich. If...
I hear ya john, and it makes sense. I'm going out to put the Holley back on. Would you happen to know anywhere that sells the thread repair kit for cheaper ...
I put the Holley back on. Fired it up and now I get loud pops from the carb when I rev it up. Also, when it heats up, it still idles down and tries to die. ...
Jeremy, I think I pulled in behind you with my 79' Coupe at tech (below the tower) at BSD. You seemed to launch pretty good. Whats your setup? My first run...
Sounds like it is still pig rich. Two words for ya. Proform mainbody. Skip the rethreading crap. Just snag a pro form mainbody and be done with it. Everyone...
As for the engine. I had everything cleaned, bored, and balanced a machine shop. They file fit the rings as well. The cam was a custom flat tappet from Ed ...
Black=Rich Blue=oil White=Steam or oil Glowing headers are mot a good sign. That mean you are either very lean causing excessive heat or very ricj causing the...
Last time my car was popping back through the carb it was a blown hg between #3 and #4 cylinder. Do a compression check. Rex ... From: John...
REX MCLAREN
rex332@...
Jun 19, 2005 4:43 pm
31351
Red pipes and white smoke mean LEAN. A loose lifter after run-in suggests a bad lobe. I think you better check lift on all your lobes. If you have a magnetic...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
