Hot Rod Power tour is going to Green Bay, my home town. I consider this a must attend event. I plan on meeting up with the tour in St. Louis, with a few of my...
... Dude... A few of my friends went last year that involved a 96 Mustang carb conversion and a 79 Z28 that had not even been broken in. I'd love to go this...
Ralph that would be perfect. Meeting in the Huntsville area would be perfect, as I know I can't make St. Louis in a day from here. Definately keep me posted on...
........over at http://www.stangpro.com . We've got our article outline, basic specs, and some pictures posted in the initial article. Assembly and, more...
Hey guys (1) Can i install Holley crab jets to 750cfm speed demon crab? (2) I got 2-73 and 2-79 jets but i have notes that the jets are bigger then speed demon...
... then speed demon holes!!! ... I don't think Demon even makes jets. They use a lot of Holley parts basically. Holley jets will work in a Demon. The...
I have an 80 Mustang coupe with an '85 302 H.O. bored .020, 9.9:1 compression, Crane Powermax cam with a lift of about .550 (have to check the specs to make...
I'm back! =) But my stang has seen better days. More to come. I picked up a 1990 GT (25th Anniversary) in the mean time. ... From: G. Pennington...
G. Pennington
gerry.pennington@...
Feb 14, 2004 6:14 am
28618
It won't go down or it won't latch? If it doesn't latch check out the striker and see if the plastic piece is still there. You may also need to adjust it. ... ...
What's your specific problem, rough running,lack of power etc? Most 600 vs carbs should be OK if it's good shape. Check for a blown power valve or internal...
Anybody know what happened to Central Coast Mustang and the GT40p heads. They aren't available from ford anymore. Dennis Hilliard had a deal with MAC to only...
They are still up and running as far as I know. I called them a few weeks ago to get a quote on an engine. They still advertise in Muscle Mustangs & Fast...
G. Pennington
gerry.pennington@...
Feb 15, 2004 6:51 pm
28622
Didn't realize that. Couldn't find their web page anymore. Did a search for dennis as well as central coast mustang and could no longer find anything. Do...
It runs a bit rough, and hesitates when going from cruising to wide open throttle. The idle mixture screws have been adjusted countless times and do...
Don't remember them having a web site. And if they did, maybe it wasn't much to remember. =) ... From: capri_16t [mailto:capri_50@...] Sent: Sunday,...
... It pretty much sucked. :) "This e-mail message is intended only for the use of the intended recipient(s). The information contained therein may be...
... What cam again? You won't tune a hesitation out w/ the idle screws. Those just tune idle. You'll likely need to swap either the primary side shooter or...
Well, I finally ordered the stuff to upgrade my combo. I got up with Ed Curtis of FlowTech Induction and ordered a set of his AFR 185s and a set of stud mount...
... AFR 185s and a set >>of stud mount rocker arms. Already pay? Buddy of mine just told me today he's selling his year old (little use) Vic Jr heads and a...
You need to do a mock up and clay the piston to check piston to valve clearance. Any modeling clay would work. Just place the gasket, and set the head down on...
Yep, already purchased, actually they just arrived a few minutes ago (I didn't think UPS was runnning today, glad I was wrong) These are the pistons I'm...
Those are the pistons i used on my buildup (306) the good thing is they have plenty of valve clearence but it will hurt c/r a tad. btw one of the thing i had...
... have plenty of valve clearence but it >>will hurt c/r a tad. <snip> Not quite as bad on a 351W as you have the xtra stroke. "This e-mail message is...
Sean, ouch, that picture is rough. I opted to put mine in storage before the bad weather came, but I couldn't hold back any longer. It's been 50+ degrees...
... the bad weather came, but I couldn't >>hold back any longer. It's been 50+ degrees here ( this place is freaky when it comes to the weather), so I ... ...
Could someone help me out here? The spec sheet with the heads recommends ARP head bolts pn#154-3603 and says to torque them 100ft/lbs, but the instructions...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
