What about in combination with the dual snorkel breather? I mean...that's already a really good cold air intake system itself. I did see a photo where some...
G. Pennington
smokinn@...
Apr 1, 2003 8:39 am
26854
Does anyone have a rear upper strut brace? I've been searching, but can't seem to find one. [Non-text portions of this message have been removed]...
G. Pennington
smokinn@...
Apr 1, 2003 1:20 pm
26855
Is it true that you can upgrade to 5-Lug and rear disc brakes all at once by using 1994-2001 spindles, calipers, disc, and axles? [Non-text portions of this...
G. Pennington
smokinn@...
Apr 1, 2003 1:20 pm
26856
Is anyone running 9", 9.5", or 10" wheels on the back? If so, does it stick out past the fender? Did you have to get the fender rolled? What ...
G. Pennington
smokinn@...
Apr 1, 2003 1:20 pm
26857
Does anyone have a Flaming River Steering Rack installed? It's a manual rack, correct? How is it compared to the stock power steering rack? Is it difficult...
G. Pennington
smokinn@...
Apr 1, 2003 1:20 pm
26858
... There is only one place for this type of information. He helped me 3 years ago with my 73mm changeover for the 84. http://www.svo73mm.cjb.net/ Ralph ...
... As far as facing forward, it does provide cool air. So it is a fresh air intake providing a denser charge which results in MORE POWER!!! Yet, it is not...
I have a manual rack, stock Ford. Just sitting it is difficult with wide tires to turn but if you are moving at all its no problem, and with skinneys like 165s...
No.......you're correct Ralph. The problem w/ the forward facing scoop is it really needs to be about 5-7" off the hood surface (ala snorkle style scoop) to...
Weld sells a Mustang specific 9" wheel w/ 5.5" of backspace. The typical rear wheel is the 8" w/ 5.5" or 10" w/ 6.5". On a Fox platform some find the need...
... wrote: <snip> I have a extra manual rack for sale for $125 and that includes the steering ... (work email is slow today so I'm sending this from the...
... steering ... what kind of mileage on that rack Ron? "This e-mail message is intended only for the use of the named recipient(s). The information contained...
... is ... Would you consider selling it minus the adapter? I want to use a Borgeson U joint instead of the rag setup. If so......how much would you want...
No, thanks Ron ... From: <sean.meldrum@...> To: <carbedMustang@yahoogroups.com> Sent: Tuesday, April 01, 2003 8:40 AM Subject: Re: [cM] Flaming River...
... Ok....thanks. If you change your mind in the next week or so let me know. "This e-mail message is intended only for the use of the named recipient(s). The...
... That sounds suspicious. The rings may be uniform, but the bores rarely are. Are you measuring them all in the same bore, or in the bores that they will...
... That sounds suspicious. The rings may be uniform, but the bores rarely are. Are you measuring them all in the same bore, or in the bores that they will...
I think this is the car you are talking about. He's got a great site and car. Looks good even though its mostly stock. http://www.duenkel.com/wes/ ... From: G....
Thanks Sean, The dot on the cam is a good point.hehe.. Thank you.. <<Cam gear........you'll want the face w/ the dot for aligning w/ the crank ... I used a...
Thanks Dennis, I measured all the rings in the same bore. The block was cut 30 over so they should all be dead on. I will compair all the cylinders with the...
Bingo! I emailed the guy the questions I had about the hood scoop. Hopefully he will reply soon. ... From: Jonathan CROMPTON [mailto:blownhatch@...] Sent:...
G. Pennington
smokinn@...
Apr 2, 2003 8:39 am
26876
... EXACTLY how I installed mine. :) Could be the replacement bearing is just a bit deeper too. "This e-mail message is intended only for the use of the named ...
Matt...... If they are file fit rings you have to check each ring in the bore it's intended for. "This e-mail message is intended only for the use of the named...
... Thanks for posting that link! I lost track of Wes's page a few years ago. "This e-mail message is intended only for the use of the named recipient(s). The...
Whack-a-doo, whack-a-doo... ... Yeah, I remember when I first threw a new clutch in the 84. I also replaced the bushing and it did not seat completely. I never...
In a message dated 4/2/03 3:40:03 AM Eastern Standard Time, ... Wes posts frequently at corner-carvers.com under the screen name WesStang. Jim [Non-text...
JGWURTH@...
Apr 2, 2003 2:19 pm
26881
I dont remember seeing file fit anywhere on the box or in the paper work that came with them. Ill check them in each bore then. I quess what im asking is if...
If +/- a little something was what you wanted, you could have bought ready-to-use rings, instead of file fit. ... From: Matthew [mailto:matthewt316@...] ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
