OK, knowing that, walk away... you're dealing with a kid that obviously LIES, and admits that he has run the car hard.. IF he was responsible for the repairs...
the lower is one end from above, the other from below. ramps are fine, but use whatever you are comfortable with. as long as its secure and safe. a lift is...
on the sender to turn off the dash light? how do i test the sensor? It look like this is the last bug a boo for now the car is almost road ready-- shocks this...
i am thinking of replacing my wheels on my 86 coupe and am having problems finding replacement aftermarket wheels. i want to use the stock 16 inch size and am...
I have figured out how to get the star hex head studs holding on to the rear of the targa top. What tool is used to get the front part of the targa roof by the...
Ok Thanks Michael, I assume the smaller torx, I will go find that tool today if possible. michael morache <michaelmorache@...> wrote: its the same size...
Matt, its best to be patient, from what I have read, this is a walk- away deal from the get go. I looked for over a year before I found my 87. And yes I took a...
are you positive that the switches are all ok? all wiring is good? if its the sender, just buy a new one..its too cheap to bypass, and with every jury-rig...
I got mine through ebay like Robert. I waited and let it drop out of bidding, most vettes do. Then I got it under his reserve amount. But I couldn't buy one...
John, On my 84 there are two connectors.. one on each side near the lights that be unplugged.. backtrack off the lights and you should find them,,,, Chuck ... ...
The lights turn on and off by little mercury switches built into each lamp housing. You can trace the wire and unplug the connector one each side. That's what...
I bought a new egr solenoid and that's just a foam filter there on the front side of the solenoid. The backside has a vaccum line going to the egr and another...
Thanks for the replies. I took it to the local automated -no touch- hand car wash and although it has a guard rail the car just barely clearly it. It'll do for...
Thanks to all, who listen to me rant and rave about my viper system, I have sucessfully removed it after many days of cussing and pulling my hair out. The last...
We went to our reunion today, where there were 2 C5's and my C4. We were all out admiring each others cars with all the respect that Corvette owners show one...
glad you got it....happy in fact....now its whole again... now go out and find a vipor on the road to torture as a celebration thing....glad is going...
The shop that works on my 91 uses Bosch. Jeff Jeff ... From: c4corvette@yahoogroups.com [mailto:c4corvette@yahoogroups.com]On Behalf Of John Sent: Monday,...
if the old O2 sensor can be removed, it often can be cleaned with a mild solvent and a lite scufing with a sand paper to polish off the carbon build up. reveal...
When I go to reverse or drive and the idle is a lil high after start up the thing feels like an old worn out truck clunkin into gear! What will make it smooth...
Yes, that definately sounds like one of the u-joints (probably one at the rear of the driveshaft) dw howle <dw_howle@...> wrote: When I go to reverse or...
I agree... There are 6 U Joints on the car and any one of them could make that noise. Sounds like it's time to get under the car. Check all the U-Joints...
... I'm having the same problem. I had my transmission beefed up and it really clunks into gear. ... Start with the U-joints and then look at the differential....
Reminder from the Calendar of c4corvette http://groups.yahoo.com/group/c4corvette/cal Horsepower at the Zoo Charity Car Show Sunday September 18, 2005 10:00 am...
c4corvette@yahoogroup...
Sep 8, 2005 9:56 am
7033
to swing a short 22mm wrench and only $21.00 for a Bosch Premium at Advance Auto. Real good news-- there is a $10 gift card mail in with the purchase of a...
Thanks, I am going to replace mine! Thats too good of a deal! See ya, DW John <vezero@...> wrote: to swing a short 22mm wrench and only $21.00 for a...
also if i'm running around 65mph and let off the gas and then accelerate it hesitates. sometimes hard start. new plugs .045 new wires new cap new rotor new o2...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
