Thanks James looks like a really nice unit, they’ve addressed all the problems of the opti, except of course it’s location. Sure would like to see a...
Hi I have replaced the ecm& maf already, But not the prom.You taked of te temp sending unit did you mean the water temp or the air temp sending unit? .The...
I took the strap off and its holding together really well. Today I'm going to grind off some of the excess poly goop with a wire brush drill bit and repair...
yeah, the water temp sensor. the air temp is only for fuel/air ratio adjustments after normal run mode takes over. engine temp is read from the 3 temp sensors,...
Rich, Any way you could share repair of door panel with some pics for other members? I am sure many others have same problem and would like to see how to fix...
Gary, I have 2 pictures of the door panel repair in the Rich's 96 folder in the photos section. There are 2 parts to my repair, reinforcing the panel ribs and...
Hey Steve, Apparently there is no such thing as too much power. one of the ZR1 guys on another forum has figured out how to build a 428 in the factory LT5...
Well Gary, you're probably right, just look at the Lingenfelter (sp) boys with 1000+ hp in the C6, something about smoking the rear tires at 125 mph in 3rd...
i'll tell ya... the panels are easy. once a process is developed like some us have done here after a little experimentation its not that big of a deal. BUT ...
Lee, Maybe when you go to finish the project you should take the entire door off the car and work on it somewhere where you have more light on a more...
well Rich, i considered taking the door off, but it was just 4 weeks ago that i fought THAT thing to get it hugn exactly right...and that is a 2 man job with...
Wow....Lee said uncle. It is funny that lee would make this post just now. I was in the garge earlier with the door panel off so i could adjust my drivers ...
Lee, what sets us C4 guys apart from everyone else is we WILL get it fixed no matter how much cursing and loss of blood it takes. I will hope that my door...
well, the glass isnt too bad...just trial & error work. move this,that and see if its getting better.. loosen the glass screws and adjust that. you could be...
I'm all done until next weekend when I will reinstall my door panel and figure out what is preventing the door from closing properly. I will check the striker...
just my 2 cents, but check for play in the hinges ...they were the culprit on my door not closing easily... richard_a14 <no_reply@yahoogroups.com> wrote:...
ok, put a floor jack under the open door right under the handle, place a wash clothe or towel between the top of the jack and the door. raise jack until it...
Striker bolt? I been looking that one but i have no idea where it is.I am looking at things and eliminating then one by one....looking the bolt you are...
Steve, I had that happen last March and took the car to a local shop supposedly good with Corvettes. He simply replaced the ECM, but that was not the problem....
Steve, What kind of 383? L98 or an LT motor? If you pass, let me know, I'm thinking of taking on a new project. My L98 has over 220,000 miles on the clock,...
It seems to be running fine at this point and this has happened after I had it in a local (Atlanta Corvette) shop along with them over tightening my lug cover...
There is a company in Cleveland, Ohio that sells "Lambo" style hinges for our C4's. (That was my idea 6 or 7 years ago, just never followed through with it, I...
Steve, Obviously, when the check engine light comes on - it should throw a code. The "stealership" probably "cleared" the codes, took your money and said,...
Thanks Greg, I will check that when I get home tonite. Steve ... From: flgraphix@... To: c4corvette@yahoogroups.com Sent: Tue, 2 Jan 2007 12:57 PM Subject:...
THATS how door alignment is adjusted IF the hinges are ok. the striker alignment is totally different. if you door seams are straight and it is not sagging,...
the striker is not on or in the door, its on the rear part of the cars chassis door jamb. its what the door latch grabs and holds onto. adjust by loosening...
I am nearly positive my hinges are in alignment as the door aligns perfectly with all adjacent body panels and does not latch too deep, at least visibly. From...
You will want to check your battery. A dead or dying battery is the most common cause of the SYS light. Also check for blown fuses in the radio circuit,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
