hey guys, my right light stoped rotating a few months ago, i believe that this has happend to others, and i was wondering how would it be fixed.........some...
Hey Michael, I paid total around 700.00 for mine here in Denver. Thats was getting the Richmond Gears from Summit and rebuild kit also then having a local Rear...
what fuse? you have relays under the hood in the nose of the car near the headlites. if the headlite still works by turning the manual knob without a problem,...
The operation to replace the Climate control dash control unit was a sucess.I was unable to take the face plate off to check the connections though, because I...
there is every possibility that you simply pulled the connection apart during the assembly of the shifter plate. thats common. while you move the plate around...
Thank you for your response to my post Lee, It is pretty obvious how 99.9% of the cigg lighter goes together because of clues that i gathered by observing the ...
It would be so nice if GM had the parts diagrams on thier website like Kawasaki does.I have a KLR650 and when i work on it if I have any question about how...
When I plugged the "cigar" lighter back in, it blew the fuse......prolly a b i g clue that I had the lighter assembled wrong. I have it assembled differently...
I have taken my 95 to the dealership and they told me my drain pipe was clear and they couldn't duplicate my leaking on the passenger's side. Yesterday, after...
lol....harry, passengers are somewhat turned off to a ride in ANYTHING that requires rain booties.... whats happening here is that the fresh air intake vents...
gary, i have the 84-96 corvette GM micro-"fish" (lol) in .pdf format..... (thats acrobat, in case you are wondering) only problem is, its 189 meg... it has...
Hey Michael, I appreciate your reply to my post. I have the 1984-2002 C4 nd C5 parts manual on CD if that is what you are talking about.I have looked at it...
... along those lines .... I have a continuing problem of dampness in the storage compartment behind the passenger's seat. [`92 Coupe] It gets quite wet in...
Traced my clutch problems to the leakage at the slave. So I am going to replace the slave. Any suggestions as I do this? Any other parts that might need...
Rich, that particular area is a part of the basic floor pan. your 2 compartments are lowered sections of the floor that can be found on the underside of the...
i figered you'd find a bad slave cylinder. there is little else that can loose fluid in the system. how to change it? i cannot help you there. i'm a 24kt auto...
I took the console cover off to put the factory shifter boot back in.While I had the plate off, I removed the cigarette lighter and moved some of the parts...
I already got the slave off. I think the fluid just went into the boot and leaked out. Not sure if it got into the clutch, I doubt it. You can see where it...
I need to have the pinion bearings changed in my differential.Since the rear is going to be opened up what else should be changed for preventative measures? A...
I'm thinking about swapping the seats in 89 coupe. The driver's side is showing wear, and I want to prevent any tears from developing. Of course, the...
Has anyone replaced their O2 sensor themselves? Any advice to make the job easier? Do you really need to have a slotted socket or can you use a wrench?...
yeah, you'll be changing just abouit ebout everything except the gears themselves. all seals, bearings and bushings have to be changed. clutchs are wear parts...
nope, afraid not. then again, it all depends on the style of seat. a sport with the latch on the front edge that rocks the seat bottom up or down will NOT...
You would think that another seat would fit in there, next year I want to put in racing seats with a quick release so I can change them in and out quick. Tony ...
under 50,000 miles. However since it does need pinion bearings ,I'm thinking to just have everything else rebuilt. The cost factor is the labor to take apart...
i am doing a rebuild as we speak... 3.54 ring and pinion from us gears for $390 rebuild kit with all bearings and snap rings $130..labor for rebuild $350 labor...
yeah i know... i did not realize that they were different until i did the exact same thing for the same reasons.. then i saw that the front lever was jammed up...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
