Hello friends, After my 82 CJ, sits for 3 or 4 weeks it takes a lot of cranking to get the fuel to the carb and start. Is the fuel draining back to the tank ...
Hi all, I have not torn the dash and guages apart yet but I have a question before I do. My oil pressure guage did not work after I got the engine in and...
Hello, I bought an aftermarket coolant recovery bottle for my 82 CJ7. I am not sure where it mounts? It looks like it will fit nicely on the left (drivers...
Hey all - If anybody is looking to sell jeep parts or a jeep, check this site out --> www.free-jeep-classifieds.com they are fairly new and listing items is...
Hi all, I am rebuilding my 64 CJ5. Got a new fiberglass tub mounted and I have run into a problem while re-installing my steering column. I installed the...
Items for sale in AZ I've been doing modifications at my own pace on my jeep. I have been collecting old parts, buying spare parts, and buying new parts. #1...
To give you my current situation, I had to cut off the bolts wielded to the roll cage to remove the dash. They didn't tell me that in the wiring directions....
CJ-7 Wiring help please. I'm doing a Cintech wiring harness on my CJ-7 and I would like someone's help who has done this before. So far nothing has gone as...
I have a 86 CJ7 5 speed transmission for sale with a Dana 300 transfer case attached to it, is has less than 40,000 miles on it. It is perfect. If any one...
I'm in Phoenix Az. I'm fully redoing my 78CJ7. I bought a Cintech wiring harness and I'm kind of having trouble with. I will continue the wiring this weekend,...
1981 Jeep CJ-7, Auto, Hard Top Make offer!!!!! New body, fenders, radiator support, tail gate and windshield frame. Body is primed ready for paint. Frame has...
1981 Jeep CJ-7, Auto, Hard Top New body, fenders, radiator support, tail gate and windshield frame. Body is primed ready for paint. Frame has been sandblasted...
I want to see how much emission legal power I can get out of my 258CI. Inline six with just bolt on parts. I will be doing that this last weekend in February...
Hi all, I am looking to put a fiberglass 1 pc front end on my 1964 Jeep CJ5A and am looking for any input on the project. Can anyone recommend one? Any tips...
Hello all am from Littleton, Co & have a 1974 CJ5. Just got body & paint done along with new rollcage & dash. Now need to do engine & axles etc. but until...
hi i have a 1983 cj7,i just installed a 4" superlift suspension on her.Now I see the driveshaft is at a crazy angle and once in a while i hear grinding from...
hi whats up im new to this group and have a question? i have an 86 cj-7 with a 4 cyl and a 4 speed i think its a sr4 and a dana 300. i wanna keep the 300 and...
Hello Group, I just recently (as of approximately 2 hours ago) have been given a Willys CJ3A. It was sitting in a collapsing garage and the Borough of...
Thanks SO much Daren. I really appreciate it Debbie ... From: Daren To: boydscjjeepsite@yahoogroups.com Sent: Sunday, January 18, 2004 5:49 AM Subject:...
Are there any good websites to look for a soft top for an 84 CJ7? My husband is looking for one. OR does anyone know of a good place to buy one. We live in...
back again: just removed the tub and found bad body mounts. rest of frame seems good, does anyone know of a shop which may have replacement parts or is it...
HI! I have a 1968 290 engine. The problem I have found is that I can't get exhaust headers for it that fit in a CJ, 290 has square ports. The 290 wasn't in...
I recently had my passenger seat belt removed from my 85 CJ7. They were kind enough to leave the bolts, and buckle by the console. If anyone has a Shoulder...
HELP!!! I need a diagram or even pictures on all the vaccume lines for my jeep! if anyone can help me out/point me in the right direction I would appreciate...
Having problems with message search?
