Dear friends, a guy from spain sent me a mail. He search for a complete generator unit for his BMW R23. All what you can see in front of the engine house. I...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the bmw-mono-club group. File :...
bmw-mono-club@yahoogr...
Nov 7, 2005 6:22 pm
3207
Hi Klaus, Did you ask MZ-B (www.mz-b.de)? I'm sure their R 25 - R 26 generator would fit an R 24 ( I haven't tried yet) and, as the R 23 was very similar...
Hi Klaus, I would add ton my first message that, after having checked them, it is possible to recoil the different parts of a generator, if it weren't possible...
... <marcuspoisson@y...> wrote: I don't think they are made anymore....somewhat scarce but can be found. Not sure if they fit /2's either. I think they were /5...
... The Reynolds Ride Off Stand was made for the /5 through /7 bikes. Here's a photo of my R60/6 with one: http://tinyurl.com/bhq6d They were not made for the...
The rideoff stand makes no sense on a lightweight single cylinder bike. Wheel maintenance is a pain also because both tires are making ground contact. The bike...
... I felt the ride off stand made my R60/2 more stable. The footprint was much wider than the stock stand, making the bike very difficult to tip over....
... making ... Hello again, The peak of my BMW years was when these stands were common, I'm sure I rolled or rode a few hundred /5, /6, and /7's on and off of...
The town I live is hilly, the streets often slope a good bit. This isn't much of a problem when the bike is pointed up or down hill. However when the slope is...
... Just checked my R26 and it doesn't look easy. The right side looks easy to put an extension on, but the left part is tucked behind the muffler. Doesn't...
... easy ... muffler. ... Just checked my R26 again. There's hope yet for the left side. Possibly a rectangular plate welded in the 'corner' made by the center...
I recently procured an NOS sideatand for my R27. Which slides on the bracket just fine and clears the header pipe too. Problem is: I have no spring. I checked...
... one, just don't want ... Page 7 in the Motorrad Stemler catalog for R26/27 shows a spring but this may be a different stand ? part # 46 53 9 024 120 also...
... The Huggett store shows that as the correct P/N for the spring, but it is NLA. For my R27, I was unable to find a complete replacement sidestand, and...
You should be able to find a spring. All of the side stands are 'dicey' even the AKKIP (sp?) the type that mounts to the foot peg. Center stands are a hassle...
If you are using your R for regular rides take a tape measure. At the worse and also easiest incline take measurements of how much more kickstnd lenght you...
I posted a pic in PHOTOS 'wood side stand' of a make-shift side stand. I don't take credit for this and don't remember if I got the pic from this group ?...
Thank you for the replies, I gather that the sidestand on these bikes is kind of rare, so kind cool to have. I only kickstart on the centerstand with my other...
Hello all, What are the correct springs to use in the centrifugal advance for the r25/3? Hugget and others specify a 9mm and 11mm spring must be used,...
... Ben, You have probably seen this diagram/parts list. It does not list spring sizes but there are two part numbers listed. Seems odd that that they would be...
... Advance Springs Mark Huggett, /2 List, 2 Jan 02 R24 - R26 Centrifugal governor: 9mm spring goes in the position where the spring is always pulled or...
Thanks, I have seen that on the /2 list, however that's what is confusing me since on my advance the cutouts for the springs are identical, the advance is...
