Hi Allan, Many thanks for your report; I enjoyed the photos. Anyone of the BMW Mono Club of the Netherlands (and all the members of this thread I presume)...
pklauberg schrijft: -- Dit bericht is verzonden met Webmail van Freeler. Ook snel en betrouwbaar toegang tot internet? Meld je aan op http://www.freeler.nl ...
Crash bars on singles, are they necessary? do they protect the bike or the rider? I quite like the look of them, does anybody manufacture a crash bar for the...
... That 50-mile tour as part of the vintage show occurred in the middle of the regulator problem. After re-polarizing the generator at home, I did not use the...
... Crash bars were an option for the R27 -- I ordered them for my R27 which I picked up at the factory: http://home.insightbb.com/~aatherton/R27a/R27a.html I...
Nice to see a lot off nice email in the emailbox. Whe like't its nice to learn a lot of the Bmw (mono) questions and repair sugestions. It, is also nice and...
Dear Allan, Incredible story about your (first) R27. It provides information about the BMW as well as about Europe of the sixties. As you probably know, this...
R en J Bakker <rclbakker@p...> wrote: "... Is it OK to you that we translate your story into Dutch, so that we can publish it in the magazine of the BMW Mono...
I enjoy your R27 page. Very nice. Thanks!!!! ... _________________________________________________________________ MSN Zoeken, voor duidelijke zoekresultaten!...
Joke Bernard
jokebernard@...
Aug 7, 2003 6:59 am
1280
Hi all, yet another new member. Although not a new owner... I bought my 1956-R26 in 1972, drove it to and from school and work for about ten years and then...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the bmw-mono-club group. File :...
bmw-mono-club@yahoogr...
Aug 7, 2003 9:06 pm
1282
A new improved version is in the file section. The principals of the 4-stroke engine are added in the drawing Always nice to see what valve is open at what...
Yep, that's very nice Ser, did you compile the valve timing information yourself, or was it from another source, book, magazine etc? Ben ... it to ... apart ...
Ben, the valve timing info was from the dutch mono-tech-manual In this book Ron Konijnendijk describes valve settings on page 182. I do not know how correct...
Hi How do you loosen the screws on the timing plate? Do you have to remove the advance unit? If so,how? The photo shows the guy useing a screwdriver. I can't...
... advance unit? If so,how? The photo shows the guy useing a screwdriver. If you rotate the advance unit so that the notches in it's side line up with the...
Hi Group, I just installed a small electronic ignition unit in my R27. It still uses the points but gives a much stronger spark. The points wont wear out...
... remove the ... screwdriver. ... line up with the screws, ... Hi John Tried for over an hour useing all kinds of screwdrivers. No luck.Removed the advance...
Hello Steve Those Velleman kits are a nice little unit, I'm interested in how they go. I designed and built a crude version of an electronic ignition for the...
Hello John This should be set so that when the rubbing block of the points is on the lowest point of the cam the points should be closed. With the timing mark...
HAs any one had the problem of the R27 getting hot and vapor locking? With the carb right where it is and a hot day in traffic I have vapor locked more then...
In a message dated 8/10/2003 10:31:00 AM Eastern Standard Time, ben@... ... Ben, I mounted mine under the seat. That way its cooling fins get a good ...
Hello Ben, I also used an electronic ignition system (self made...) 18 years ago on my R 27 I'm yet restoring. I had it concealed under the tank, in the ...
Hello Harry! Two main possibilities: - you remove the advance unit, as you say, or - you buy 90 degrees screwdrivers, which help a lot, in this case Third,...
