whom ever, I am interested in building a non typical trike with a springer frt.end Vtwin motor tube chassis non typical rearend (maybe from a saturn or...
Hi Bob sorry I do not what the rear is out of . Bart ... From: bob To: bikebuilders@yahoogroups.com Sent: Thursday, April 14, 2005 11:02 PM Subject:...
Chain dive,belt drive,shaft drive ? Have you got a motor ? I'm guessing you've seen the low slung Trike from Excile Cycles. While I havn't seen that episode,I...
If you haven't seen Excile's trike,it's in the center spread of the April issue of Back Street Heros. (the British mag) No doubt it would ride better with some...
Ian, I have an old Virago to use as my test project and it is shaft drive. I did see Excile's trike and it is close to what I am doing. Do you think that the...
Bart, thanks for the picture maybe some good ideas and for sure automotive of some kind (looks like) bart fifield <bwfifield@...> wrote: Hi Bob sorry I do...
Here is another.Very similar layout,rigid,chain drive, different wheels and tires. < http://www.paulyaffeoriginals.com/pyo-projects-nanettestrike.htm > Do you...
... ..snip ... Jag IRS rear ends should be reasonably cheap to buy and quite cheap to get parts for, you shouldn't pay much premium over a Chev or Ford parts. ...
Darren, Yes thank you, I also posted a few pictures of one that was from france that I got from a guy in Austrailia, also pretty cool. bob in ohio darren...
MY EMAIL ONLY TOOK 6 DAYS to make it on the list, great list! post 14th, shows up the 20th with same answer saw 6 days ago........... ... From: "darren"...
The Yahoo Groups system has a mind of it's own, sometimes there are random delays, but that is probably the worst example I've heard of. Unfortunately,it is...
There was some cool trike drawings in Easyriders, probably over 10 years ago. The one that sticks in my mind had a very wide single car tire on the back,V-twin...
This is a Roth trike with a Ford small block. It has been modified for two people, originally single seat as a hard tail, now has a I.R.S. from a small Ford...
I don't think this is classified as a trike but it is different. Uses a jack shaft to another chain between the two wheels, solid axle. Was at the Donny Smith...
Hello Paul, What is the blue machine against the wall behind the trike? A home-made PullMax or home-made Yoder? The blue machine is a little fuzzy that far...
The blue one is a louver press, the grey one is a Pullmax and there is also a english wheel and a planishing hammer in there somewhere. I was really learning...
Thanks Paul. I have an E. Wheel and I am setting up a section of my shop to make more sheet metal items. I have built a tank to display my paint work and...
Mark Nugent is hosting The Second Annual Pounding in Peculiar on May 21-22, 2005. Welding demos, metal shrinking, E-wheel, metal spinning, and more are on the...
Attention ALL Metal Maniacs: Just a reminder that this weekend is the Second Annual Pounding in Peculiar, May 21-22 2005. There is still time to pre-register...
The list has been dead lately, so here's a question. I'm stretching a Sportster tank and kinda want to seal it. What tank sealer have you used that works the...
I got an incredible interest rate on my home loan, I am self employed I refinanced my home. This service can help. http://www.greatrefi.com/?a=rcc1 take 30...
Larry i used the por-15 and it has done me right so far so i'll keep using it..one thing i always do is clean it 2 times and on the 2nd time let it set over...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
