Hi does anybody have any drawings or advice of/on pedal box assembly,previous owner has obviously put it together wrongly as ive spent over £250 up to now...
Hello there, Are all the seals ok. Have u the servo connected. I once put the calipers on up side down but thats a different story.. All the best Jay Ivey.. ...
Hi Jay, yep all seals are fine and servo is connected but that shouldn't come into play during bleeding i dont think,just not got any pressure at pedal.......v...
Can u send me some pics of it all, mite spot something wrong. Probably easy to do if I was there.. C ya Jay Ivey.. ... From: TONY MURRAY <mrry_tny@...>...
i would normally start at wheel farthest away from master cylinder.using a volunteer to pump pedal until only fluid came from the pipe but my poor brother has...
Hi Tony Is the clearance between the push rod of the servo booster and the piston of the master cylinder correct 0.5 - 1mm till July 1983 or 0.3 - 0.7mm from...
Cheers Guys, finally got it done with help from Matty P.........OWE HIM A LARGE BEER........oh and when i put calipers right way up once hed pointed it...
I seem to remember someone asking about a perspex windscreen a while ago. There's a 356 Speedster perspex screen going on eBay… I'm not sure if it will fit a...
Trev, Â I have seen that ! Â Just wondering how much work it needs to polish the scratches out ! Â I also enquired if it came with fixings....... sadly not...
Hi Alex, Good point, polishing scratches out is almost impossible as the polish itself will also leave scratches :( Speedster glass frames have an alloy...
Trev  I have perspex side screens (removable hard top) at the minute as unfortunately i am without garage (not for long i hope) - These are ally and then...
I have been trawling for some upgrade ideas on the pyder and came across this extract froma skoda forum..... Just a quick note from a Paul Banham Spyder...
Hi I'm not sure if your aware but the whole electronic ignition set up swaps straight over from the pre93 favorite (1.3) the dizzy and 'brain' are all you...
Hi All It's been a looooooong time but the car is still underway. Does anyone of an Estelle which is currently being broken or where I can find the whole front...
Hello all. I would agree with matty p and go with the favorit one. Make sure you get the right coil to match tho. Not a performance thing but can help with...
Hello there Rob, Good to see you are still cracking on. I have a front suspension unit as new and not used. Its wide track, cars after 84. Would let it go for...
Hi Jay Thanks for the offer, I was hoping for a full unit with Axle, Wishbones, Hubs, Breaks etc etc, so I could offer it directly up to the underbody. Out of...
Hi I have seen in your pictures that you have have hinged you rear clam shell from the inner side of the car so you open it from the engine bay. I have done...
Have you not got any suspension at all for the front then? You not got any calipers on your car. My front suspension has hubs,discs, dont think I have any...
I have all the components but the problem is it has been left for so long, and I have been out of the country that people started using my workspace as a bit...
I went with a "Hot Spark" unit that came from the states (found it on eBay). It uses the Hall effect and replaces the points in the standard dizzy. 2 wires,...
Hi to all,new to this car building mania. Can anyone please tell me were to purchase a complete replica kit for the 550 spyder(banham)as the link stated is...
Hi Godwin and welcome to the forum. The Banham 550 Spyder is produced by Martin & Rowena, there phone number is +44 (0) 7721 339633 As far as I know they don't...
Thanks trev for the info on the new kit thing. However I would appreciate an e-mail address of this new supplier, thanks alot and keep on posting. Godwin Malta...
Hi Godwin, I'm unable help with an email address. Someone else on the forum may have it. It maybe worth sending a txt to Martin's mobile requesting an email...
Hi All, Im off to see a Banham this weekend to potetially buy. Can anyone tell me what to look out for when buying a second hand one of these? A quick responce...
Hi Huw Is it a project or fully built, is it SVA'd if not can it be made ready for SVA, has it been MOT;d, check body for cracking etc, do panels fit ok, is it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
