Hi guys Well the RA has finally got to me and I have to sell the Spyder. Is Ebay any good to sell and what should I ask for it- any ideas Spec not yet SVA'd ...
Hi all Due to the dreaded RA I have to think of selling the Spyder, I was thinking of Ebay or one the magazines but would welcome input as to where and roughly...
Just a quick straw poll for the newark show. 1) who is planning to be there? 2) which day? 3) bringing spyder? I am planning on being there, with spyder,...
I'm hoping to be there both days with spyder Regards Mick ... From: Nikhil Dholakia To: banhamspyders@yahoogroups.com Sent: Friday, June 13, 2008 12:48 AM ...
Finally! Took two complete SVA's and two "resits", at different sites, for someone to finally pass it. Think we're going to put up with a Q plate rather than...
Looks good Richard. Well done for getting it legal. Are you bringing it to Newark? Mine took two resits too with mirror problems. Borehmawood has taken over...
Probably not going to make Newark, it's not running too well at the moment. To be honest I've had little to do with it recently due to work and other ...
Lee  have i just spotted your spyder on Bas's website ?  He bought mine (the yellow lpg one) earlier this year, hope the sale goes through as sweet as mine...
Hi Rob, I spotted yours on his website, as soon as he told me it was LPG, I knew whose car it was. Sale appears to be going fine. What he sells it for is his...
lee  he did offer to collect, but i haggled on the price and had a last run to the docks with the roof down, and hitched a lift back with one of our...
Everything is going fine with my sale to Bas. I would back rob's comments about dealing with Bas, he has be easy to work with. He told me he is looking to...
Looking for some help really -  I have got a nice momo steering wheel i would like to fit to the spyder - having difficulty finding a hub/ boss kit for...
Hi Alex Halfords do a Mountney boss number 076, you may have to redrill some holes to fit. Regards Mick ... From: Alex Till To: banhamspyders@yahoogroups.com ...
Hi i am currenlty trying to figure out the spacing (distances) of the porsche script badges and the emblem from the edge of the bonnet and rear end - any info...
hi everybody iam hard at work on the car well every night the car was nearly completed when i purchased it the clam shell does not fit as well as it should by...
Hi All Due to a lack of garage space, I've had to relocate my Spyder to my Mother's in Hull. Are there any members reasonably close to there who would like to...
I just kept slicing bits off the arches until the clamshell closed without fouling..........there is only an inch or so left of the outer arch, but it will...
Newark was great. 3 spyders were there. Mine managed its first long run and behaved itself for 300 miles - Horray Is there a big performance difference between...
if you go for a 136 - you will need new inlet and exhaust manifolds. i think your present 105 ones would also fit the 130 engine - although check to see if the...
the 136 (9.7:1) motor has a higher compression than the 135 (8.8:1) but the same as the 130(9.7:1). if you pull your 136 from a single injection car the head...
the best 136 head is one from a feliicia MPI as this has multi-port injection, and will bolt onto any 136 rapid, felicia or felicia block 1) - far better...
hi the skoda 130 l ihave has an s shaped metal fuel filler pipe so the hole in the rear wing would have to stay. i would like to fill this in isee in the...
mitchell - i think that on bills car the filler pipe may have had a section taken out and then rewelded - a dangerous procedure which my welder refused to do...
if anyone has problems with this, which can be a problem esp. with the older swing axle 105 or 120 based cars, a solution is to do what we did in the picture...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
