my speedometer cable recently broke, i bought a new one and tried to replace it a few weekends ago. a book i had was vague and i cant get the cable out from...
it should just pull out. remember to remove the cotter pin, or in my case a finish nail. you may have to cut the old one or keep wiggling it to get it to free ...
there is a rubber ring that is around the cable where the cable goes into the back of the wheel, is that the cotter pin? i can get the rubber ring out but then...
the corret pin is just outside the grease cap. sometimes the part that goes thru the grease cap gets hung up in the spindle. but it should just slide out, ...
the clip is on the outside of the hub cover... MIKE www.offroadvws.com ... From: tromb_rob67 To: bajabugs@yahoogroups.com Sent: Saturday, May 01, 2004 7:45 PM ...
hey all anyone know how to make a cable longer or a bus one shorter also anyone know how to get a speedo to read right with a set of 35"tires as I seem to have...
I have came upon this problem as I have 36" Buckshots on my Baja. I could not find any reducer to recalibrate the speedo, so my wife and I traveled on the...
Dude, that's one of the tallest VW's I've seen. Do you drive it much? How's it handle? In a message dated 5/3/2004 1:08:18 PM Eastern Standard Time, ...
street69baja@...
May 3, 2004 8:19 pm
12833
the car is street driven all the time handles well just don't off road ... From: street69baja@... To: bajabugs@yahoogroups.com Sent: Monday, May 03, 2004...
The rear tires are 36" with IRS stock trailing arms and the front are 32" It is street legal. What I did was, took swing axle spring plates and torsion bars...
Got any pics. i would love to see it. Arnold Norton <vwsandndirt@...> wrote: The rear tires are 36" with IRS stock trailing arms and the front are 32"...
I don't know how. I just don't run one because i keep snappin it. When I got my inspection notice they never even noticed. i still have my speedo, just no...
I thought I would try something tonight, and started at message #1 and read each and every message, in order, untill I could not see straight.......accually...
...must be a VW thing. I find myself actually reading most of the traffic on this list, I dont exactly go back and reread them. I'm on a couple other car...
I think I'll stick w/ my adjusters in the ft end & turned torsion bars in the rr. It's no ware near as tall, but my 205/60-15's ft & 235/75-15's rr are a lot...
street69baja@...
May 4, 2004 1:23 pm
12840
I would cut an approximately 3-4" hole opposite of where the pedal cluster mounts to allow access to the existing fuel line, and for access to the clutch cable...
vwn2zs
vwn2zs@...
May 4, 2004 4:30 pm
12841
Ya thats a good Idea! I think I may give that a try. Thanks, Mac ... Do you Yahoo!? Win a $20,000 Career Makeover at Yahoo! HotJobs...
i am thinking about chopping to top off of my baja, but doesnt this weaken the body tremendously? would a typical roll cage be enough reinforcing, or would...
drew, the originals were just bug without bodies. yes it does weaken them some but i think its worth it. the one i have now has been chopped for at least 10...
check into super beetle cables, it was slightly to long for my stock suspension travel baja (more preload) MIKE www.offroadvws.com ... From: Tim Johnson...
are you worried about frame/tunnel integrity? i guess thats what the roll cage is for. MIKE www.offroadvws.com ... From: vwn2zs To: bajabugs@yahoogroups.com ...
I like your Baja. A couple of questions........ Where did you get the spring plate covers? (they look kewl with the matching valve covers) What type of turbo...
the spring plate covers are vintage claudes buggies I used the same turbo set up and the orginal 2bbl but am now in the process of building a 4bbl intake I'm...
Hey Skinny, you going to the Ypsi Michigan show on the Weekend of May 22-23? We are hoping to make it there in our BUS that we got going right now. Art in...
things are in the air as my wife is ready to bring a new member into the fam so it might not be a good time ... From: OurBug To: bajabugs@yahoogroups.com Sent:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
