For sale, never assembled Aztec 7 kit. I purchased this Kit several months ago but just don't have the time to work on it so I decided to put it up for sale....
This may be a dumb question and some of you folks may roll your eyes, but my aztec is running fine with it's 1600 bug engine, but when I turn off the key, it...
Hi Chris...sounds like ignition switch is worn, or has moisture/corrosion inside. Try turning it repeatedly. Next disconnect ' ign' ignition wire from...
Chris, I was going to respond, but Dave hit the nail on the head. I do have a question though...I got a Type IV 2.0 engine from a VW 412 for Nate's car. Any...
Hi Chris Dave has some good points . If it still does that when that wire is unhooked check for a short. More than likely you will have one someplace where the...
Does anyone here know of any Aztec 7's available for trade? Please see this gentlemans request below... He also sent some pictures of his TVR if you would...
I recently purchased my first Aztec 7 and i cannot find any parts for the damn thing, it is near impossible. does anyone have any information on where i can...
I have a few things available here on this site: http://kitcars.irth.net/aztec7/parts_supplies.html Otherwise, let us know specifically what you need and...
Looking for Aztec 7 kit or unfinished project. Type A preferred. would like to have all glass but chassis and drivetrain not needed. I just bought one on Ebay...
I have a kit for sale that has never been fully assembled, sorry do not have the glass but do have all the fiberglass parts including seat buckets, if...
Does anyone have any parts or spare parts for sale? I need just about everything. Seats, center console, headlights, taillights, windshield, etc. Even if...
The original seats that came with this kit were just molds right? you had to have them upholstered? You could use any type of buckets in there as well I would...
hi spencer , we got to be careful about the heigt of the seat . i buy 2 leather corvette 95 electric seat and they was 1 1/2" too hight even w/drop floor . so...
As far as the seats, I used some seats from a Fiero and they work ok. You just have to have them reclined somewhat to avoid getting in the way of the door,...
for seats: Check Pepboys for an inexpensive low-rider bucket or racing model (about $150-200). There's a fiberglass shop in Savannah, GA that could make a copy...
I have been to Shannon's site many times. Great stuff there. I bought my car a few years ago on eBay and then had it brought into Canada. I have not registered...
Are the original seats very close to the floor? How comfortable are the originals? Would you be able to use a set of recardos or other aftermarket racing type...
hi , i find an other aztec7 in montreal area , but that one have no serial number . i heard 8 years ago that some guys around had made mold from the aztec7 in...
Actually, yes, the original seats are quite comfortable. they offer some good side support, but may not be comfortable with someone with a wide wasteline. I...
That is a nice looking car. Damn, wish I had money. I would buy another one. Then I could be considered an Aztec hoarder for having more than one. Spencer...
hello group, I have an aztec7 unassembled for sale, as far as I can tell, it has everything needed, except for the windshield, they gentleman I got it from,...
Darrin, It's Rich Quinn from Ft. Stewart, GA...will you sell the door windows separately? Do you have the door latch/handle assembly? Blessings, Rich ... From:...
No, sorry, but I won't break the car into pieces and sell them off. If i don't sell it as a whole, I'll just put it behind the barn until I'm ready to build...
I haven't heard this, but if anyone gets a chance to try, please let us know! --CG a_z_t_e_c_7 <a_z_t_e_c_7@...> wrote: hi, ive heard that a pontiac...
