... New entry? = Yes Name = William Lacal Location = Port Washington New York serial number and type = 1 of each type history = 2 cars, 1 type A 1 type B....
I recieved this email on June 15th and thought I'd forward it onto the group. Jack can be reached via email here: jgwest_94595@... ... Hi Chris, We are...
If you're really board, here is an annecdote regarding the Bertone Carabo which is the inspiration for the Aztec 7... The anecdotes you hear about the film...
Does anyone have any information related t the FiberFab Scarab 3 Wheeler. These were made in the 70s. Any photos, dimensions, etc are appreciated. Thanks - AB...
Hey everyone, in the event you didn't have a brochure from the Aztec7, I scanned it and put it in the photos section. The date of purchase on my car is 1984,...
Darrin, Welcome home chief!!! This is Chaplain Quinn. If you can scan me anything on the door assembly I would be most appreciative. I'm still trying to figue...
Hi Chaplain, thanks for the note, I will look at the manual I have and scan what ever I find for the door mechanisms. I didn't realize you were an active...
Jon just finished his Aztec 7 and it was just registered a few days ago. Se sent me some pictures and more info on the car so I've upted his Regestry page...
Folks, Further research into the side glass replacement dilema has produced this information: Option 1: You can have your window openings changed to accept a...
Has anyone use on of these with the 5 speed yet? I might end up with an Aztec on a Ghia pan with that engine in it. I was concerned about close to 200hp back...
I have a turbo-charged 1835 cc VW hooked to a Porsche 5 speed on a VW pan and it works fine. Had to replace shocks with coil overs and modify length of trans...
LBfairguy@...
Oct 21, 2004 10:32 am
163
Thanks Leon I know a bit about Volkwagens but wasn't sure about how the 5 speed went in. I apreciate the help :) Rich ... VW pan ... modify length of...
Hi Rich, I went crazy trying to figure out how to mount the tranny onto a VW cradle until I got help. It really is fairly simple. First, remove the...
LBfairguy@...
Oct 21, 2004 9:07 pm
165
To: cguenther@... CC: Subject: Re: Miura windshield Date: Thu, 28 Oct 2004 19:48:32 -0700 ... Special order Estimated at $2,250.00 USD Delivery 6 to 8...
Here is a weird question for the group. Ok now does anyone know of a good guide for values on kits? It's not easy to get something when nobody knows what to...
Not so much looking to sell anything as much as looking to see what it might be worth. It would be nice if there could be a guide set up for kits. I would...
Hello out there I hope all of you have enjoyed the holidays so far. What would be nice is a heated garage and a good selection of CDs. So spend the winter...
For sale, never assembled Aztec 7 kit. I purchased this Kit several months ago but just don't have the time to work on it so I decided to put it up for sale....
This may be a dumb question and some of you folks may roll your eyes, but my aztec is running fine with it's 1600 bug engine, but when I turn off the key, it...
Hi Chris...sounds like ignition switch is worn, or has moisture/corrosion inside. Try turning it repeatedly. Next disconnect ' ign' ignition wire from...
Chris, I was going to respond, but Dave hit the nail on the head. I do have a question though...I got a Type IV 2.0 engine from a VW 412 for Nate's car. Any...
Hi Chris Dave has some good points . If it still does that when that wire is unhooked check for a short. More than likely you will have one someplace where the...
Does anyone here know of any Aztec 7's available for trade? Please see this gentlemans request below... He also sent some pictures of his TVR if you would...
I recently purchased my first Aztec 7 and i cannot find any parts for the damn thing, it is near impossible. does anyone have any information on where i can...
