toyota tundra v6 and v8 has overhead cams with shim type (non hydraulic) valve "buckets" which do not require adjustments unless you have very high miles, or a...
... done at ... I am assuming nothing with this truck. I'll be off next week and will take the time to run down the entire list that was attached to the ...
Happy 4th, kids! Just discovered a hole in my driver's seat (leather), came up as I was cleaning it. Pretty sure I pinched it into the seat last time I pulled...
Does anyone know what company sells upgrade gears for the 4x4 Tundra? And what would be the advantages/disadvantages to switching the stock gears to something...
Hey Neel. Yeah, it's been a tad bit wet around here this weekend. However, this isn't putting a "damper" on the local holiday festivities! As for your seat...
While I don't know who makes them, I can tell you the effects of different gearing. Lower gearing (larger numerical numbers): a. more torque multiplication b....
Not sure about your efforts to find an aftermarket seat...but I know something you can do to cure most of the vibration. I took a cheap toothbrush (broke brush...
Hey Tim, Im not sure why you sent me this message? I have an 06 Tundra with a Airaid (cold air intake)JBA Headers and a CUSTOM 3 inch diameter exhaust system....
I am in the process of buying a 6 cyl/reg cab/automatic/ac/2wd..2006 Tundra..The problem I am having is I really don't like the Phantom Grey pearly or Desert...
John, Sorry about that. Meant that to go out to the group. All I meant was that I'm not assuming any maintenance was done by the previous owner unless it was...
Not a problem dude. As far as the performance issue, YES, I had the JBA headers, the CAI, and the exhaust done at the same time. What I had them do on the...
Toyota's website says that the Tundra Reg cab V6 Auto comes in the following colors only: Black, Phantom Gray Pearl, Desert Sand Mica, Salsa Red Pearl, Natural...
I saw that.I was wondering if they can have a different color ordered from the factory?Silver particularly.... Thanks Randy ... cab/automatic/ac/2wd..2006 ... ...
Thanks for the input Chris. Aren't you running 35's also? If you could would you change the gearing and if so, to which gearing ratio? Thanks, rich ... From:...
I have 265/70-17 tires.. They're about an inch taller than the factory 265/65s, but not enough to warrant a different gear set. If I have large monster mud...
Sounds like I need to rethink the cold air intake. I was planning on holding off on that since I just dropped $40 for the K&N filter last month. First,...
I have a 2004 double cab tundra. I put a K&N Intake and filter with the flowmaster two chamber system. Awesome sound and increased gas mileage. I didn't...
I just said that I had the Airaid C.A.I. and the JBA headers and the custom exhaust all done at the same time. Someone else asked me if I noticed a difference...
Thanks again Chris. Is Dash still around? Rich ... From: Chris To: awesometundratrucks@yahoogroups.com Sent: Thursday, July 06, 2006 2:13 AM Subject: RE:...
I have been trying to find a Tundra club here in Alabama or in the southeast. Havent found the real deal yet. [Non-text portions of this message have been...
Oh yea you can find those nerf bars on ebay. probably about 3 different dealers. And I am looking for someone trying to sell the flatter looking stainless...
... different ... looking ... flatter ones. But ... ones to ... You should probably stay away from chrome plated steel nerf bars in favor of the stainless...
Hello Tundra-ians I just purchased a 2001 Tundra with 65k miles. About 10% of the time when the auto trans goes into overdrive, there is a significant clunk...
rich i called and got some gear prices and im ready to order some. ill see
if i can find the info for you. where are you located? im in eugene\ Dash [Non-text...
Sound like slack somewhere... I'd check the u-joints, and then both for and aft point of the driveshaft.. where it enters the transmission, and the rear end...
Dash, would you mind posting your info? I think this is good info to broadly share across the list. What ratios are available, and their price? Who is the...
Hey Dash, I'm in Hawaii,on the isle of Oahu. Zip here is 96786. How's everything going? rich ... From: Dashiell Terry To: awesometundratrucks@yahoogroups.com ...
Does anyone know what type of threads are on the crank shaft bolt? I can find nothing that would indicate they are left handed, but since the motor rotates...
Greetings - Q1)The headlight lenses on my 2000 4WD are cloudy on the top halves on the outside, probably from dust abrasion. Is there a product that will ...
I have used Mother's Plastic Polish (red bottle) with a microfiber towel. If your lenses are severely beat... you may need to use a buffing pad to polish the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
