Hi everyone. i am still trying to find rotors for my 73 100 coupe S. the Lucas catalogue list the rotors for a 1973 as a 279mm x10,5mm non vented. my car's...
Hello, my friend, I have bad news for you ! LUCAS never made such air vented early Coupe S front rotors !!! And my knowledge says that not even ATE made such...
Thank you Theo for the update is there another solution or am i stuck keeping the car in the garage and just sit in it once in a while. it seems they are still...
Hi, I have been reading your correspondence with interest. What about a machine shop? I would also try various hot rodding associations as they specialize in ...
Normal machine shops CANNOT machine AIR VENTED rotors ! ONLY single mass steel rotors ! Theo as Racer ... a machine ... specialize in ... garage and ... ...
Depends on what you are want to do. If you do want to keep it in original condition, I'm afraid that there isn't any alternative way (except some PLASMA job,...
Hello Audi fans, François, you should try the companies listed in this website: http://www.jmc-auditeile.de/ Maybe you'll find what you need. Happy motoring, ...
Thank You patrick. i did try them but after a few e-mails gave up since i never got an answer. i also by the way like your web site and am very familiar with...
Try Essex? http://www.essexparts.com/pands.html In a message dated 03/10/2006 9:17:25 PM Eastern Daylight Time, faloppaf@... writes: Thank You patrick. ...
CNC? http://cncbrakes.com/cncbrakes.com-asp//cr.asp?grp=cr In a message dated 03/10/2006 9:17:25 PM Eastern Daylight Time, faloppaf@... writes: Thank...
This is an UPGRADE modification/solution and not like an original replacement equipment or an "original" remanufacturing job. And please, don't forget that...
An inquiry will cost the gentleman nothing, n'est pas? In a message dated 04/10/2006 5:57:56 PM Eastern Daylight Time, no_reply@yahoogroups.com writes: This is...
Hello François, I go to the Bethune meeting evry year. Nice place and nice people. Regarding the rotors, did you try this link : http://www.akautoteile.de/ ...
Hi, I need help with tuning the carburator of a 100 GL. Someone took it apart and put it back together with the consequence that all adjusting screws are moved...
Hi Gerben, From my experience in N. America, I can advise that the carb should only be adjusted by a carb rebuilder / specialist. This is not a do it yourself...
This is not a matter of turning both adjusting screws as per the Audi repair books. It must be set up precisely / tested or it will not work properly. Better...
OFF TOPIC: No disagreement, Andy ! You say the correct and logical advice ! Theo as Racer ... should only be ... yourself thing, ... garage cannot ... PROPER ...
Thanks for the replies on the brakes. i took the brake rotors and calipers apart but i noticecd i need to replace the lower ball joints. the question is: are...
The lower ball joints are the same for all the ealry typ803/801/815 cars. The different part in this area is the lower ball joints' carriers... These are not...
Hello, I am located in Holland, and I want to ask all the members a question about renewing the exhaust system. My Audi 100L 1.8 motor is the type with the...
Hi Dirk, The North American Audi has a resonator near the front of the car (under the middle of the car) and the muffler at the rear. I put a heavy (not sure...
Hello Audi fans, Dirk, I baught 3 years ago a stainless steel exhaust muffler in Holland, for my Coupé S 74'(same brakes and rear suspension that your 100...
Hi Dirk If you don't mind ordering from the UK, there's a place in Sheffield that had in stock many original exhaust parts when I got a system for my 71 Coupe...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
