Anthony: If you go to the following site, and search for "sway bars" you'll see a wide variety of bars, and as you work your way through the site, all the...
anyone got any dyno or timing changes experience with a de long 13mm intake cam. I find the cam gives power at 6200+rpm, and that's a bit high, for my...
While not race track conditions, my newly resurrected Berlina, running Mortimer's former engine, was getting 11 mpg on the street. This is with a big valve,...
this is a bit much, no? Should be 16-22 street driving? Must be running a bit rich. I would get close to that (~10mpg)on a day at LimeRock (mostly flat out)...
My Milano/75 proved yesterday it can handle a very tight "Miata" type autocross course, winning Street Modified over 6 others and finishing 3rd out of 89 cars....
I second that! ... From: Wil Painter To: alfaracing@yahoogroups.com Sent: Monday, November 08, 2004 9:19 AM Subject: [Alfa Racing]: Re: Alfa wins again Way to...
List, Greg Gordon is furnishing alot more than the supercharger brackets for my autocross car. I'm getting pretty much a complete installation kit from him. ...
Congratulations Bill! Keep that Alfa out front where the should be!! Todd Redmond ... From: Bill Sims <Bill-Sims@...> Date: Monday, November 8, 2004...
Any of you have an early Alfetta 4th gear laying around ? I need an Early type (course cut gear type) for the pinion shaft only (gear count is 29). Will buy...
Without taking it apart, I really dont know, other than the clutch shafts were not tapered (had the same size bearings at the flange end and at the flywheel...
Richard, I've got one, 29 coarse teeth. It's boxed up & on your way to your home address via UPS Ground. It's got a pretty respectable synchro ring too. Mike...
Thanks Mike, how much do I owe you?? How`s your wife`s recovery comming? Unfortunately, I`m embarassed to say I cant recall her name, but my memory and some...
In a message dated 11/9/2004 12:28:54 PM Central Standard Time, alfar7@... writes: The Mazda sold the week of the hurricane. Went to Missouri. A grandpa...
Group, I finally started to time-trial my giulia spider. I'm using 185/55-15 Pirelli's on 15" Panaport wheels. I am looking for a softer compound tire that...
I recommend British Avon CR6 ZZs which are held by two stockists in the USA. They are a higher profile than your current tires but a very good road-legal...
nick savage
nsavage51@...
Nov 10, 2004 2:45 pm
7633
I was reading all the brake posts and was reminded of a convesation I had last summer with a guy who was vintage racing an old 101 spider and claimed he was...
... Has ... Steve, Won't work on a 101 because they didn't have ATEs, but many Porsche 911 models had an ATE caliper identicle to the Alfa ATE but alloy. Seen...
I got this idea from another list. On this Veteran's Day, I was wondering how many veterans are on the list. Please list yourself. I wanted to Thank them for...
I've been contemplating how to get my mostly street '73 GTV go around the racetrack (Summit Point, VIR) a bit faster at club events. I've never been happy...
Hi Bruce, Either the Watts link or Panhard rod improve the handling by lowering the rear roll center. If you draw a line between the front & rear roll centers,...
George Schweikle
schweikg@...
Nov 11, 2004 5:55 pm
7641
Dr. Al Mitchell is currently serving in the military as I understand it. ... From: Curt Griggs To: alfaracing@yahoogroups.com Sent: Thursday, November 11, 2004...
In a message dated 11/11/2004 11:09:00 AM Central Standard Time, bgiller@... writes: I have been considering putting on either a Watts linkage from Andy...
There has been discussion on the 750-101 list, Tom Lesko did a fair amount of research. Best bet seemed to be an aluminimum Outlaw caliper for about $100...
Russ is right on about the quality (or lack thereof) in the Zat parts. I threw away some suspension parts I bought from him on the advice of Paul Glynn who...
... Ok, both are lateral locating devices; Panhard's are common as they are simple and cheap running across the width of the chassis on end pivoted on the axle...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
