Ok, I'm new here, got tipped on another forum when I posted some questions about the Alfa V6. So I'm posting it here too, hope you don't mind. ;) Just a quick...
The 2.5 is a brilliant motor, but in modified form it obviously depends on who did the mods and the quality of the parts used. Here in South Africa a certain...
Mike sounds odd to me, I've seen longer although I'm not certain what rpm they turn...I'd have figured the stock car guys run 'em that long. Wonder if there is...
Mats- Please tell me about your coilover setup!!! Could you post some pictures? Thanks, Mike Cudahy ... From: matsstr To: alfaracing@yahoogroups.com Sent:...
Thanks for that Phil. I've e-mailed him. I'll let you know what comes of it. Thanks again, Mike Cudahy ... From: Philip hehir To: alfaracing@yahoogroups.com ...
I have found several outfits that say they can make me one, around 9 lbs. Tilton makes a 7lb starter, and they can apparently make a custom one, too. I am...
... I'd have to crawl up an' see what the fattest diameter might fit but I'd think a 4" wouldn't be any sweat if the shifter was located outside the tunnel ...
Guys, Mats has a charge air cooler stuffed in his 75 big enough to keep a Peterbilt frigid ;) Hi Mats, ... The bottom end is hell for stout, standard prep...
... Mike, I'll see if I can pull one off a 105 rear and see. ... Good question ;) Scott __________________________________ Do you Yahoo!? New and Improved...
Sorry for the non-racing content but I need some help in Nebraska. Details here: http://www.alfabb.com/bb/forums/showthread.php?p=56925 [Non-text portions of...
... motronic 10:1, and the Borgo 10.4:1? I've a new set of the 10.4 Borgo on the shelf: part # 66.7222.0 std, less rings and pin, 442.5g (No wonder they're...
Hi Scott Thanks for the reply. Dimensions of the ports themselves and the path in and out I will leave to my cylinder head guy, He knows whats needed. I'll do...
Hi Mike Can't really help you with my coil-over setup as I bought the car a few weeks ago and all the stuff was done by previous owner. I can tell you that the...
... don't know Mats, cam makers tend to use different points of lift to advertise the degrees and duration, i don't know if there is an industry standard in...
quick responce on several subjects: V6: It is extremely durable, and can easly make lots of power. I have lots of history with the motors and suggest the...
Matbe you read my post a bit quick? Can't use a 3.0, 2.6l is the maximum capacity in the class. Driveshaft? Have never had any problems with them, just use NEW...
... [are you sure?!!] 9:1 Standard 440gm 10:1 Motronic 470gm both have steel reinforcements ... near enough. tapered wall pins 97 gram intended for 500gm...
Thanks for the pic! Once again I'm amazed by the crappy geometry in the Alfa heads... :) ... the ... on ... front ... 10%, ... on ... for ... Well, I'm already...
RJ ?????? *****Have finished rear suspension and close ratio transaxle with 5.5 clutch & flywheel for lightweight Alfa Spider( yes you read correctly, my new E...
Whatever you are smoking, I want some ; ) ... From: alfar7@... To: alfaracing@yahoogroups.com Sent: Saturday, October 02, 2004 8:25 AM Subject: RE: [Alfa...
Now that Carrera shocks are gone for the Giulia's, what are good alternatives? I've heard of dual adj Koni's, anyone else running them or are their other ...
Looking for a set of 14x6 Panasports (need not be racing) for my Super race car. Preferably in the Northeast. Also have a set of 15x7 Racing Panasports for...
Russ, Carrera has been sold to AFCO or someone in the North Central states. No longer in Georgia. I'll try and get that info or do a search. I have used Rughs...
Anyone looking for a set of Carrera shocks for a 116, Milano or GTV-6? I had a set custom made for my Alfetta and will not be using them after this season....
