More $200x stuff.... anyone know where I can find 2 Mondial pistons and liners- for a 2.0L, stock 9:1 compression? New is best, but used will work. I've got 2...
Eric, Just curious, how is this turbo project going to go below $200X? Are all the parts "donated" or "bought for $50" (ahem...) ;-) Zamani ... and liners-...
Lads, Just a quick question about those square rubber engine mounts on the 2L GTV engine. Is there anywhere you can get uprated harder ones for racing purposes...
Zamani, Keeping the cost under $2000 wasn't that hard. Granted, we got lucky finding some of our parts, like the exhaust manifold. But the rest of the engine...
One of the tricks I've had success with is stiffening up the gearbox mount at the rear. Beefing up this mount with an elastomer works quite well, but you...
I know I neglected to say this but the engine is in a rear engined Skoda so the rear mount is effectively my gearbox front mount. This is probably why I have...
I have seen them out of nylamid (spelling and language?) in a GTV that has an F3 engine. The guy still claims he feels LOTS of vibration and can only hit...
Does anyone out there in Alfistiland know the size of a stock rear sway bar for a 1979 Alfetta Sprint Veloce. I just measured mine to be 22.3 mm. Is this stock...
John, I sold my E Prepared '78 Sprint Veloce, so it's not available for measurement. Your rear sway bar is 7/8 inch, which I think was stock. That's what my...
Hi--how much work was involved in installing the strut brace?--Do you think it could be installed in the GTV-6? (the engine taking up much more room!) thanks, ...
Alan Lambert
lechefgerard@...
Mar 7, 2002 8:06 pm
2475
Alan and Group, Strut brace was practically a bolt-in. Did have to bend one of the braces that goes to the firewall so the wipers would still work. And had...
Attention Sydney Down Under Alfa Drivers, If you are interested in taking your Alfa for a good drive amongst fellow Alfisti, send me an email. I'm organising a...
I have a 105 series weber manifold, screw in thermostat type, bead blasted with 45mm carb mounts. The manifold has been machined(looks original) so the 45mm...
Hey All, In my zeal to rid my GTA block of the foreign material we found inside, i drilled out nearly every oil galley plug I could find prior to cleaning the ...
Steve Schaeffer
borrani@...
Mar 10, 2002 1:06 am
2480
Go to any hardware store and buy what ever set screws they have. 5/16 are quite common and close to 8 mm. You might even find some 8 mm ones. Buy the...
Can any of you racers help with hot or cold pressure suggestions for Toyo RA1. I'm running a 75 3.0 with about 1200kg weight at the moment. Regards, Peter...
peter
eurosport@...
Mar 11, 2002 1:55 am
2484
35 psi front 31 psi rear 4 pound split front to rear, check with a pyrometer. -Peter [Non-text portions of this message have been removed]...
Peter L. Krause
pkrause@...
Mar 11, 2002 2:20 am
2485
I recall someone on the list had one for sale. If so please contact me. Richard Jemison...
alfar7@...
Mar 11, 2002 6:53 pm
2486
I have a 40 mm weber manifold in excellent cond. Good rubber mounts with a pair of 40 Delorto`s, that I was going to sell to a racer in south Fla. but he has...
alfar7@...
Mar 12, 2002 2:36 pm
2487
I'd like to buy it-thanks , Roy in NJ ... From: alfar7@... [mailto:alfar7@...] Sent: Tuesday, March 12, 2002 9:35 AM To: rhworthington@...;...
Oppedisano, Roy
roy.oppedisano@...
Mar 12, 2002 2:41 pm
2488
Can I have anyones opninon about my expressionistic painting of dale, on EBAY, my first try, (just an opinion). thank you,keith http://pages.ebay.com item#...
What is the current best wisdom for trans fluid in a 5 speed with the usual toasted synchro? Thanks art d...
riverside@...
Mar 12, 2002 6:29 pm
2490
My preferences? Redline MT-90 or MTL. "Wisdom" differs among peers, however. Mike Valant www.mev.cc ... From: riverside@......
Michael Valant
mvalant@...
Mar 12, 2002 6:52 pm
2491
The graphic isn't bad, but your post is TOTALLY without Alfa content. ... ===== Best Regards, Alan Lambert __________________________________________________ ...
