Not approved yet, but I have reason to believe that the limited prep Fproduction Alfa classifications will be modified to allow weber carbueration and also a...
Hey, y'all. Long time no.... Lost a computer and couple of hard drives... Just getting back on my feet, as it were... I recall someone had a TO bearing assy...
... not true--I've profiled the 2.0 flywheel for a 1600 ring gear and extended the release bearing carrier. I used a HD/late 1600PP. But the problem is that ...
... it would be used in a bus with the type 1 engine pre 73 as the later ones had guided release bearings here's an aftermarket unit one ebay 290088733392 ...
Jon Norman at Alfa Parts, (510) 525-9435, sells an aluminium flywheel with a 1600 ring gear which accepts a 2 liter Alfa clutch and pressureplate and fits...
I like what Gary just suggested. Another way to go, IF you have the parts around, is what I ended up doing. Over the years, I had uprated my 66 to a 2L with...
Paul Spruell wrote: Hi Steve, The 1750 had 110 teeth, the 1600 had 105 and the ID of both are the same. Either starter will work with both ring gears. The...
Paul Spruell
paul@...
Dec 9, 2008 6:31 pm
12190
I guess no one out there is racing in the snow.........it's kind of quite here! Well, I am working on rebuilding an engine for the Little Green Spider, It was...
I'm about to pull my LSD to clean it up. Will be wearing a t shirt and have the garage door open..today will be in the low 70s.. Autocrossing and road racing...
... AT 40 below, you (literally) don't have to quote which scale you're using, Bill !!! That's where the two scales cross one another !! :-) Greg (good on cold...
The silence was killing you, wasn't it Eliseo? As for watching races this year, I would think that a guy who owns 2 race cars could afford to race one of...
To all: I know this car well. Raced it several times especially in enduros. Great car, reliable. No financial interest, just helping out someone who has...
I have a friend who races a Giulietta spider. He is convinced that he wants more negative camber in the front. To make a long story short, what is the...
Hi Bill, Not that I am a font of wisdom on the matter(!), but I think that unless you have a very liberal rule book for your racing series, then due to the...
... he wants more negative camber in the front. ... accomplishing this? Has anyone devised adjustable upper arms? ... Use shims on the lower a-arms....
Using Shims on the Lower Arms is the tried & proven method. But to get back to where it once was, the bottom frame rails may have to be pulled back out and...
Thanks to all, He has run out of threads while shimming the bottom out. By pushing the bottoms out, he is close to tire interference with the fenders. Thus,...
Bill, We have had good results from modifying the upper arm to supplement the shim adjustment of the lower arm. We have milled the mounting surfaces of the...
Paul Spruell
paul@...
Jan 29, 2009 5:56 pm
12202
Folks, THAT is why I subscribe to this list! Instead of conjecture, we have facts. Thanks, Paul! [Non-text portions of this message have been removed]...
selling a set of JE 85mm pistons for 2.0L w wrist pins,locks, total seal rings for sale. brand new, in the wrappers. also, electromotive coil pack and...
Does anyone know of a rear sway bar application for a Giulietta Sprint? I have a 1" bar on the front and handling is reasonably balanced but it does understeer...
I have some pics of my bar (built from light 4130 tubing. solid stock is just too much stiffness) on the rear,on the 101 Giulietta racer that is very simple...
Gee, Pete. I've NEVER driven a Giulietta race car that pushed! <grin> Try trailing the brakes into the corner. [Non-text portions of this message have been...
We never had problems with our super close ratio gearbox in the EP Spiders, so the spare just sits in the trailer. We are now a distributor for OS Giken, a...
Paul Spruell
paul@...
Feb 4, 2009 8:38 pm
12210
It's not bad and I'm still sorting it. You're right . trail braking does work. _____ From: alfaracing@yahoogroups.com [mailto:alfaracing@yahoogroups.com] On ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
