Howdy Racers, Where are you putting your electric fuel pump, in the trunk or under the car ? I have a fuel cell flat on the floor of my super ( no original...
Dan: I mounted mine under the right rear corner, one of the options you're considering. Used a bent plate with Lord mounts to isolate vibration. Picture posted...
Dan; Mine (in GTV6 with stock EFI pump) is on the trunk floor about 8" to the right of the fuel cell, mounted with rubber isolators. Fuel cell top is flush...
My engine builder says that my crusty old carbs are too far gone for a rebuild. I need a good used pair of Weber 40mm DCOE's. Preferably with 32mm chokes. ...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the alfaracing group. File : /Driving...
alfaracing@yahoogroup...
Nov 6, 2008 4:29 am
12141
The memo below regarding SCCA changes to driver suit requirements is effective 11/1/2008. If anyone wants a copy of the Word Document with photos...
I'm wondering what could be so wrong with a Weber to render them not re-buildable? I have seen the tangs that hold the float pin broken off (repairable) and...
Personally, I would never wear a racing harness without a full roll bar/cage. Do you really want your head, neck, and back imobile and locked in an upright...
... Eric, you raise a good point, but I think a lot of it depends on the car, and the use. In the case of an open car, or an older race car, I fully agree....
Looking for advice to remove the glass windsheild on a GTV, as well as the plexi rear, hopefully without breaking either. -- Peter Inshaw president Plotter...
Glued or gasketed? If gasketed, my advice would be to cut the gasket and just order up a new one next time around. If glued, then get a good utility knife and...
Two pieces of broom handle and a length of safety wire.....or was that a gangster movie I saw........ One handle on the inside, one on the outside, the safety...
I need to get rid of a Kamm tail racing chassis. Car has no suspension but does have a cage and a logbook. Car was run in the San Francisco Region of the SCCA...
Second that. Thanks for bringing it up Todd. ... From: Todd Redmond To: alfaracing@yahoogroups.com Sent: Tuesday, November 11, 2008 7:09 AM Subject: [Alfa...
Yes, not said enough, thank you all for taking the job of all jobs and putting yourself at risk for our country. It is appreciated -- Peter Inshaw [Non-text...
Yes, not said enough, thank you all for taking the job of all jobs and putting yourself at risk for our country. It is appreciated -- Peter Inshaw [Non-text...
My small, late model Bosch starter finally died so I'm looking for an alternative to replacing it with another Bosch. I remember seeing a Titlon starter adn...
Curt; Did you try Andy Kress? I got one from him a few years ago and it works great. Dick Giambra ... [Non-text portions of this message have been removed]...
My idler on my Montreal race car has worn out the replacement lower bush in the idler a tad faster than I would have thought. I presume the stress of 225/50 ...
Count those flywheel teeth, Curt. And call, Mike Besic at 630-469-5626 I'm sure he can sell you the "right one" Ken _____ From: alfaracing@yahoogroups.com...
... If you want to get carried away: Hard chroming the shaft is great start. Then make a bushing out of nitralloy, and have it nitrided. I learned decades...
I need to purchase a .86 fifth gear set to complete one of my super close ratio gearboxes. If someone out there has a spare to sell, please contact me. I...
Paul Spruell
paul@...
Nov 20, 2008 11:01 pm
12165
Paul- The Milano boxes have .87 fifth gears in them. Are these useable in your setup? Richard, this is your specialty. Where you @ my friend? ... From: Paul...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
