So, I re-discovered an old autocad file with a crank scraper for a 2l (Mike Valant gave me the file years back), will it fit/work on a 1750? I used to know all...
In a message dated 10/2/2007 3:30:22 PM Central Daylight Time, zman521@... writes: http://video.google.com/videoplay?docid=-5815350492893860613&pr=goog-sl ...
Bugger. The sump bolt pattern is the same though? Ben ... _________________________________________________________________ Advertisement: Your Future Starts...
Ok, I can still use a large chunk of the design then... Ben ... _________________________________________________________________ Advertisement: What are you...
Jim, I used one of your crankshaft girdle / windage trays designed for a 1300 on my 2000 ITB engine. I had to cut to clear the ends of the connecting rods...
Russ, I have them for the 2000 too . . . there is a small difference between stock rods and Carrillo's. The stock rod requires more clearance because it uses...
Hi Jim, which way is the No1 cap position different? (although I suspect the No1 cap location isn't a problem, been so long since i've had a sump off an Alfa...
OK, so ignoring the Dunlops that I can't seem to find discs for (even though I've finally got the system working reasonably well with them), which is going to...
OK, so ignoring the Dunlops that I can't seem to find discs for (even though I've finally got the system working reasonably well with them), which is going to...
Won`t the early 105 hubs & disk fit the Dunlop spindle? I recollect so, but... If they do its easy to build a adaptor to mount the Brembos. (see Giulietta pics...
Answering my own question... poked around on Mikes old site, found a picture of the tray installed on a 2l. http://engr.smu.edu/rcam/cpm3v/gsrebld/gsblock1.jpg...
Completely hadn't thought of the bracket solution... don't know why, i've got access to a CNC mill and i've got a set of bike brake caliper adaptors sitting on...
Ben, the 2000 has the main cap farther forward. My design for a windage tray is a little different than yours . . . it attaches to the top of the studs to...
My 1300 Spider loses power on left hand turns only. It is an instant reduction in power that is instantly corrected by turning the wheel back to center. This...
Look down in carbs through jet cover , remove jets & see where fuel level is. Sounds like that could be the issue? If elec. tach should reflect. Rj ...
Sorry, I forgot about mentioning that fix. I already pulled the floats, checked them for leaks and reset them. But I haven't checked the fuel level after the...
Solution for fuel level issues. Raise it. its either fixed or worse, if worse lower below orig level. if that does not do it Have a beer, and another, as...
Jim said "And FWIW the 750 series engine is different than the 101 but no one in his right mind is going to race one of them ;-)" Nobody ever said anyone on...
In a message dated 10/4/2007 10:17:07 AM Central Daylight Time, pkrause@... writes: Nobody ever said anyone on this list was in "their right mind"! But...
Hi My 72 GTV leaks transmission fluid onto the clutch and out the bell housing only when driven on the track. This used to be just an annoying mess, but now...
Have you dhanged the front seal in the transmission? If it is pretty new, it might have gotten installed crooked. Or it could have been defective. Inspect...
Ok, my Drawing has the spacing between the slot for the rods at 92.08mm between 1 and 2, and 3 and 4, and 93.66 for between 2 and 3. Is that spacing going to...
____________________________________ This is NOT a standard set of input gears (which are 22/31), on TZ/SZ and 102 5 speed transmissions, as well as "split...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
