Last weekend at Mid-Ohio, I had an "ear" break off of my tranny output yoke where it mounts to the Giubo at about 7000 rpm in 5th. The ear, the attached bolt...
I've wondered if it were possible to run a one-piece driveline without the donut and support bearing. Is your setup with the carrier bearing or is it a one...
1) Alfaholics (no affiliation sells a transmission output yolk and front drive shaft for use with a "standard" u-joint. NOT CHEAP but how much are the...
FWIW, the 1st generation Mazda RX-7 had/has a vibration problem in the drive train (apparently due to the engine being offset in the chassis, closer to the...
I'm about to rebuild my transmission and i realize that my 1600 duetto has an older style transmission. Anyone know of a source for old style syncros? Or...
I suggest just changing them out. You probably can leave 5th alone it generally is OK. You can turn the existing slider ring to use the other side of it. The...
I took in trade for a pair of cams a complete FI system from fuel pump to belt cover. (fuel pump, filter, Spica with all lines , working TA, manifold with ...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Hi Group, Looking for 11:1 forged pistons for 3.0 24V. If you have any info/contacts please let me know. Would like low expansion type, so Venolia may not be...
... JE fits the bill but they're getting a bit big for their britches. Talk to the folks at Ross http://www.rosspistons.com/index.php I don't have a contact...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
Thank you for your email. I'm out of the office until July 23rd on vacation and will reply upon my return. Best Regards, Nick Fonte www.dynamic-flowform.com...
