I was talkingon the phone with one of the stewards yesterday afternoon when they hauled Paul`s EP red Spider up to impound on a flatbed. It was described as...
Reminder from: alfaracing Yahoo! Group http://groups.yahoo.com/group/alfaracing/cal Racing Chat! Sunday March 4, 2007 1:00 pm - 3:00 pm (This event repeats...
alfaracing@yahoogroup...
Mar 4, 2007 2:58 pm
10862
Reminder from: alfaracing Yahoo! Group http://groups.yahoo.com/group/alfaracing/cal Racing Chat! Sunday March 4, 2007 1:00 pm - 3:00 pm (This event repeats...
alfaracing@yahoogroup...
Mar 4, 2007 7:57 pm
10863
Since it has been so quiet, I thought I'd get opinions on this from the group. I've been going through the rear suspension on the GTV and noticed the...
Mine is setup purposely with a nose down attack angle. (My diff setup is fully adjustable) I'm told it's to help traction by inducing more squat when the...
Phil, I assume your set up guy was referring to the positioning of the upper link and lower trailing arms. These can affect "squat" or "antisquat".....love...
Erik, You always want a little angle in the driveshaft or the u jiont in going to run in the same spot all the time and will wear out. By having a little angle...
Bro, The most efficient driveshaft placement is the one where the u-joint angle coming off the back of the transmission is exactly the same (opposite) as the...
Reminder from: alfaracing Yahoo! Group http://groups.yahoo.com/group/alfaracing/cal Racing Chat! Sunday March 11, 2007 1:00 pm - 3:00 pm (This event repeats...
alfaracing@yahoogroup...
Mar 11, 2007 6:56 pm
10869
I am going to help a friend turn his "86 bone stock spider into an autocross car. I would appreciate any suggestions on how to increase the power and handling...
Art, Contact George, per Russ. He's been campaigning a D Street Prepared Spider for years. George was very helpful when I considered making my '57 Spider...
my $0.02: in that spicer joints are not CV joints, and thus introduce a non smooth motion in the shaft(costing energy), you would want to reduce this factor as...
Went ice racing the other day(BMW 530 on snows) saw a honest-to-god sprint car out there on menards, it had a funny lateral locator assy of two arms and a alum...
Go to http://www.speedwaymotors.com/ they sell several versions of Jacob's Ladder and all the sprint car stuff. A sprint car on ice, eh? That is a totally new...
In a message dated 3/14/2007 10:07:21 PM Central Daylight Time, alfaneely@... writes: Go to http://www.speedwaymotors.com/ they sell several versions of...
It would make sense to me that less of an angle would result in less energy loss, but I was told by somebody once that u-joints were designed to be used with a...
Heck, everybody else has spoken on the subject...whenever there is any driveshaft angle, you are imparting acceleration and deceleration in the driveline with...
Reminder from: alfaracing Yahoo! Group http://groups.yahoo.com/group/alfaracing/cal Racing Chat! Sunday March 18, 2007 1:00 pm - 3:00 pm (This event repeats...
alfaracing@yahoogroup...
Mar 18, 2007 2:13 pm
10880
Thanks everyone for your comments. I wasn't really concerned about u-joint wear because the diff is constantly moving up and down enough to make the needle...
Reminder from: alfaracing Yahoo! Group http://groups.yahoo.com/group/alfaracing/cal Racing Chat! Sunday March 18, 2007 1:00 pm - 3:00 pm (This event repeats...
alfaracing@yahoogroup...
Mar 18, 2007 6:59 pm
10883
I run an Australian based amateur web site called www.MotorsportArchive.com I am about to publish a page on my web site devoted to Alfa Romeo driver Horst...
Russ, because you are sooo... special, please don`t read my next post....... Rj ************************************** AOL now offers free email to everyone. ...
I have for years hoarded a Spica manifold that has 41mm Butterflys. I am a master rules expander, and I cannot tell by looking that this is not a stock 37mm...
I am trying to get a set of 14" Minilites on my 67 Alfa Duetto race car. I
cant find the lug nuts to fit. They are the shank style with no bevel. The
hole...
