I need an '82-'83 IT175 intake boot if you still have this one. From: YamahaIT@yahoogroups.com [mailto:YamahaIT@yahoogroups.com] On Behalf Of Gerry Meier Sent:...
Hi Guys, Well I'm finally getting the motor apart on my 79 IT250 resto-rider to fix the trans. When I got the jug off, I found the piston to be marked 1.0,...
that would be .040" over...aka 1mm, you should be able to buy pistons up to 2mm...aka 2mm. ... From: Mel To: YamahaIT@yahoogroups.com Sent: Saturday, March 14,...
1.5 & 2.0 , which Wiseco still makes them . The Dirt Shack Lee Buchanan , Owner 326 Bamber St. , Mammoth Spring , AR. 72554 1-870-625-0164 phone Vintage Dirt...
I couldn't find the 1.5 or 2.0 on the Wiseco site, but I found one on ebay. The owner says its a single ring piston however. The piston I took out has two...
'77-'79 are the same...2 rings The Dirt Shack Lee Buchanan , Owner 326 Bamber St. , Mammoth Spring , AR. 72554 1-870-625-0164 phone Vintage Dirt Bike...
Hi guys, Anybody got Timken numbers for steering stem bearings? And how do you get the bottom on off without tearing up that rubber seal? This is a 79 IT250,...
Wow, NE Arkansas. I was born in Jonesboro. My family was from around Leachville and Ravenden Springs. First bike I ever rode was a Honda mintitrail in my...
Thanks for the link. I'll spend some time exploring that site for sure. I don't see how I'm going to get a grip in that bearing, but I guess I'll figure...
Measure the diameters and look at the timken listings. That's what I do? ... From: Mel <littleplanes@...> Subject: [YamahaIT] Re: Stem bearing #s To:...
The bearing numbers for the IT175E,IT425E and IT490K are all the same,so I would guess that the 250 is the same. Top bearing---KOYO 32005JR 25id,47od,x15....
Do you like Yamaha IT motorcycles? It's time to evolve... Website: http://www.yamahait.com.au Global Forum: http://www.yamahait.com.au/forum A superior way of...
Dave, Very good info, thanks. After I decided to sacrifice the seal, I was able to get the lower bearing off pretty easily. Good to know the bearing comes...
I have a new OE piston and rings......not sure what overbore it is , but , I'll check....I think it's 2nd over . The Dirt Shack Lee Buchanan , Owner 326 Bamber...
I checked and I have a 3rd over piston and rings . These are OE . $85 including shipping . The Dirt Shack Lee Buchanan , Owner 326 Bamber St. , Mammoth Spring...
Dan, not sure if you have done your break in yet or not, but the Yamaha Service Manual for my IT250k/IT490k states to run a break in tank of gas mixed at 14:1...
actually , running a mixture of 14:1 will tend to make your fuel/air ratio lean , as more oil flows slower through the jets , so you get more air.....not good...
I can't get the swingarm bolt out on my 79 250. I've beat it with a 2lb hammer and it wont budge. I figure its corrosion, but thought there might be a trick...
No trick....soak w/penetrating oil , then , drive it out . Yes , they can get pretty corroded . The Dirt Shack Lee Buchanan , Owner 326 Bamber St. , Mammoth...
Well, got it out. Not sure I'll be able to use it again. Really had to beat the crap out of it. Here's a question...Can I put a later alum swingarm on this...
some times there a b23232 soaking and some heat ! unless the bearings are bad just pull the bolts from motor lift out at front first , my 425 had bad...
anybody know where i can find a stock tank for a 82 it 250 or 465 ?? and does anybody need a new 175 tank reproduction clark tank with decals never had...
Hello Randy and group, I mostly lurk and learn here. I love the group but certainly don't consider myself as knowledgeable as many of the guys on here so don't...
i have an 84 IT200 and might need a tank. anyone have anything half decent? To: YamahaIT@yahoogroups.com From: yert@... Date: Wed, 25 Mar 2009 08:03:35...
Hello fellas, I need some advice from the IT community. I have a 1978 IT400E that has a tranny issue. It shifts nicely but jumps out of gear when given a lot...