http://www.cycleworld.com/article.asp?section_id=3&article_id=771&page_number=7 Good stuff! Let's get on it! I want Super Hunky back in the saddle! ...
I NEED TO KNOW THE CARB SETTINGS FOR MY BIKE I GOT IT USED FOR $850 AND ITS IN REALLY GOOD SHAPE. I AM CLEANING THE CARB NOW BECAUSE OF THIS... I WAS TESTING...
while its off, set the idle at about 2-3mm open(look at the slide opening) set the idle mix. at about ¼ out as a starting point On Sat, Jul 5, 2008 at 5:34...
The pilot air screw should set to three-quarters (3/4) of a turn out for a base setting. Further adjustment will be required after engine is warmed and idling....
what does the idle screw need to be set at? From: Erik Ludwig Sent: Saturday, July 05, 2008 8:51 PM To: YamahaIT@yahoogroups.com Subject: Re: [YamahaIT] 1984...
ok I have 1 screw with a white adjuster on it and another to the right of that one with a nut on it as well From: william fox Sent: Sunday, July 06, 2008 9:04...
Okay, the screw with the white thumbwheel on it is the pilot air screw. The other with the jam nut is the idle screw. There is no base setting for the idle...
Not sure if this is applicable, but if the gas was off means you were running out of gas which will make the engine rev because it has more air than fuel....
don't have any gauges From: tim pearce Sent: Monday, July 07, 2008 5:07 PM To: YamahaIT@yahoogroups.com Subject: Re: [YamahaIT] 1984 YAMAHA IT200L CARB ...
Hi I'm trying to find the timing mark on the crankcase my 1981 IT175 ! The only thing I can see is a rounded part on the case, no scribed line or punch mark....
It will just be a judgement call on the idle.. Something like bop bop boppyidy bop bop boppidybop,,, LOL,, Just get the float level , idle air screw close, and...
So after Googling Names(brands) and Numbers (sticker) on my IT i have found the fallowing Adds have a little under $200 in Maier parts (front fender,hands...
Odds are that you have an Answer Products muffler w/spark arrestor pictured there. -Roy V ... From: "william fox" <modster.93@...> So after Googling...
its all stock other than the bars and chain. I don't have any gauges either I have an odometer but its not turning its stuck at like 450 KM no ignition either...
I don't have any light switches From: tim pearce Sent: Wednesday, July 09, 2008 8:04 AM To: YamahaIT@yahoogroups.com Subject: Re: [YamahaIT] Aftermarket? ITs...
Mine was striped of all un-needed parts(side covers,lights,switches) As it is its almost like a MX bike..only i have a kick stand...lol I dont even have a kill...
in australia its law for enduro registered bikes to come out with blinkers/ hi/lo beam head light, horn and tail light so my it490k had to have them all plus...
hey i was out on the 84 it200 in the trails and turned off the bike to pass to my buddy after about 2 hours of riding. i hit the kill switch it turned off but...
Not normal for sure, and the presence of gas means you for sure have a bad main bearing and seal. If you grab the flywheel I expect you will find it has up and...
Are you looking at the nut? Sometimes hard ware isn't machined to the best tolerances. Look at the cdi rotor, it's probably made to tighter tolerances. But if...
The crank seal is most likely the problem then. It is possible to just bend the threaded part of the crank. Sent from my Windows Mobile® phone. ... From:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
