I put a DG pipe & silencer on my 1980 IT175. Does anyone have these on this bike? I need to know what jetting changes that were made. I've messed mine up. The...
I doubt anyone is going to be able to tell you what jets to run. You'll have to tune it yourself. Does it have the proper air filter and filter oil? What...
Probably one or two up on the main and the bottom ,, Hmmm, Well I had to drop a few sizes on the pilot and a different needle.. www.sudco.com for parts.. Tim ...
Thanks for all the advice. After receiving my new gaskets I followed some advise and took the Piston and Cylinder to a recommended Cycle shop in Madison AL....
Call me , Lee , at The Dirt Shack , tommorrow . I am open from 9-5 . I'll do what I can to help you . Have a good night . ( The Dirt Shack is my Vintage...
All: I ran across this site a bit ago ( www.superhunky.com ) . After reading some of Super Hunky's "Don't Ask" articles on www.offroad.com today I was...
Gerry, Not trying to burst your bubble but I always assume that every bike I purchase and attempt to restore/ride will need a complete motor rebuild. At the...
Albert, Thanks, Yes I am now gearing up for a full motor restoration. I will be having the crank rebiult by (Mr. Crank.com) in Kentucky. I have my new piston...
My neighbor has bought a bike (Yamaha 125) in Woodland Hills, Ca. and needs it transported towards Seattle. If you are near or go near Woodland Hills on the...
hey everyone. Today i made an attempt to repair the broken third gear in my 1982 yamaha IT250 or so i thought. I split the case and got everything apart and...
Check out my IT490K, it's nearly finished! Disc breaks front and back, White Power 48mm front shocks and much much more... This is going to be a great bike...
As you now know, gears don't usually break. If they do, the remains tend to shred everything else inside the case. What was the problem in the first place? I...
... You are incorrect when you say that it's going to be a great bike when it's finished. It will be the best bike ever !!!!! Unbelievable how good it looks,...
Very nice let us know how she runs with the upgraded suspension!!!! Glen 81 465 ... From: jock.davidson <jock.davidson@...> Subject: [YamahaIT] IT490K -...
... How about some detail about how the rear disc was slotted in. Did you use Yamaha hubs ? What brake master cylinders and calipers did you use ? Dave R...
Looks like mid 1990's KTM forks & wheel...can't wait to see details on what you've done, especially the rear disc. Beautiful bike so far though. Mine's...
The forks, front wheel and the caliper setup look like they're from a KTM. The rear too, with the wheel flipped as KTM is left side drive. I'ld like to know...
I Really Want to pull this bike out of the mothballs and ride the damn thing. But its way too tall. I Already cut the seat down and it seemed to help but its...
my stock 490k is better.......then i woke up.....lol.....what carb settings are u using.... Â --- On Fri, 27/6/08, lenaandsamn <lenaandsamn@...> wrote: ...
You need to take the fork springs out, then you can see how far the forks go before they hit the underside of the muguard. The IT is a tall old beast,...
Just put one foot flat on the ground. If you have to lower it you can cut the damper rods and springs in the forks, disassemble the shock and add a spacer....
I'm from Pennsylvania USA how did you guys make your bikes street legal? I am looking for information on a street legal conversion in Pa. Thanks for any help ...
I'm in TX ________________________________ From: YamahaIT@yahoogroups.com [mailto:YamahaIT@yahoogroups.com] On Behalf Of g Sent: Sunday, June 29, 2008 10:50 AM...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
