The spokes are loose on the 175 I just got. When I pulled the rim, the inside is severely corroded and the nipples are one with the spokes. Do the 175's and...
Use some penetrating oil and a torch to loosen them up. _____ From: YamahaIT@yahoogroups.com [mailto:YamahaIT@yahoogroups.com] On Behalf Of lenaandsamn Sent:...
Hi all - I realize that this is an old post, but I have an answer that others might find useful - believe it or not, footpegs off a suzuki DR650 fit on this...
I have been researching this too and found that the '87 YZ125 peg part number is the same as the IT200's. IMS makes a footpeg for '87 and up YZ's in their...
Hello, Thanks for answer. I'm not sure that YZ125's footpeg are OK for IT200. I've had both bikes (2005 YZ125 but it's the same than 2007) and tried to install...
No I said 1987 YZ125. The newer YZ's are completely different (I have one of those too). I checked the microfiche last night and 1984-86 IT200 has exactly the...
Service Honda (they also do Yamaha) list the rear spoke set 4V2-25304-00-00 at $66.54 and the front spoke set 2W6-25104-02-00 at $44.22 less shipping and...
Sorry for the mistake (07-87)... Alain ... From: erik ludwig To: YamahaIT@yahoogroups.com Sent: Saturday, May 03, 2008 8:32 PM Subject: Re: [YamahaIT] Re:...
Hey guys, Do the Yammies with this Yeis system all have a whurrrriiinng sound when they are under acceleration,,, Kinda like the old rotary valve CAN AMS. Or...
They don't sound any different - especially not whirring. If you could hear low RPM intake noise it would theoretically sound slightly different since it...
You don't have to. If you are VERY careful you can use a pick, pierce the seal and pry it out, but care has to taken not to nick the crankshaft or case. I...
Thanks! - Figured I would replace it since I am planning on replacing the clutch plates and springs... ... pierce the ... crankshaft or ... have to ... basket...
- I use a self tapping screw welded onto a 'T Bar'which I use to pierce the seal then ease it out of the housing. It recently worked well on my Yamaha DT175MX....
Anyone remember the center stands offered by yamaha. I had one on my 1980 G model. Noticed on my 1977 model it too has the bosses for a stand. Has anyone ever...
... Here in the UK I don't think the center stands were ofered as an accesory. I have a 1978 US model IT175E and have noticed the bosses too. I was toying with...
If it is the factory silencer then no. The stock unit uses baffles inside that create and maze for the exhaust gases to pass through, and therefore requires no...
I'm tring to get an IT175 I bought off of E-Bay and right now I'm felling a little taken to say it nicely. Bike was "supposedly" running just needed carb...
There is no hard and fast spec for compression, but here are some guidlines. less then 100 psi or less - bike wont run 125 psi - may run by bump start, but...
Try this quick test - Take the plug out. Kick it or push the kick starter with your finger in the plug hole - the compression should blow your finger out. If...
All, Thanks for the replies I got my compresssion guage today.Removed air filter from air box, installed gauge in spark plug hole, held throttle wide open and...
Sorry to hear the number is so low, but at least you know what you are dealing with now... -Roy V ... From: "Gerry Meier" <rgmeier3@...> All, Thanks...
Tore the top end off and everything looks OK as far as I can tell. There are a couple of things to note. The head nuts came off very easily and once off the...
Most dealers won't know anything about pressure testing. You can make your own like I did. If you search old posts there are instructions. You need to...
What is your ring end gap? What is your piston Clearance? Is the bore out of round? While it is apart what is the big end side clearance on the rod? (it is...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
