OK, I order new brake shoe, they come in, get installed. Now I'm thinking, "Time to have some fun, right!!" WRONG!!! The clutch is SHOT. I can move the bike...
I found a few old yamahas in a local bone yard for bikes. I got a partial frame number of 24X from one and another of 5X6-003405. Any ideas what these might...
Hello, You found a 1983 YZ125 (24X) and a 1982 YZ490 (5X8) I am looking for an original Yamaha (NOS) front fender for a 1980 or 1981 IT175 (the white one not...
My 82 IT465 has a 44 tooth rear sprocket. It was great for flat out riding in Utah, but, on the hills and trails of Oregon, I need a bit lower gears. I have...
Anyone know where I can find the rubber intake manifold that connects the carb to the engine cylinder. It is also the cover over the reed valves. Maybe some...
The engine surges at idle and through mid range. above that rpm it is smooth. Surged so bad on Memorial Day of this year that it flipped 180 on the trail,...
Thomaston 's Dam CT. trip today... Me and Jeff will be heading up there this morning, get one last one in before they close. The GhostRider ... :) 94'XR250R /...
Hi all! I have an old 78 IT175 that I have had since 82. I just got the old thing running again, runs great. I found a web site that has had various NEW old...
Very cool site. But it seems there no order to the parts list and the number don't match the oem number. Is there a trick to finding the right part? ... old ...
Ken, Not exactly sure what caused this, but my guess is an air leak in the case past a seal or perhaps you're choke has debris and bypassing fuel at low rpms...
That's pretty cool, while we're on it, I have to give kudos to my local dealer, Doraville Yamaha (Doraville, GA). They have a knack of having things I never...
Yes there is an easier way. They have a link to yamaha's site, so you can find the part number you need. Then use their part# search to see if they have what...
The 5X6 is an '82 YZ490. The 24X is an '83 YZ125 Joel in Keller, TX (DFW area) '66 Corsa w/air '63 Greenbrier 4spd '63 Greenbrier 8dr 4spd "Bob" '63 900...
Anyone have suggested carb jet number for operation from sealevel to 2000ft elevation. Bike is currently jetted for SLC Utah. (about 4500 - 6000ft) Thanks for...
Thanks for the help with the ID! I am going to spend more time there and actually see what they really have, what is decent and usable and then make a repost....
I have an 81 IT465. I have recently found an 82 YZ490. I am looking to update IT's rear wheel tire to an 18" so that I can take advantage of a wider variety...
The front end should be easy. The rear wheel I'm not sure on but you will need to check the width inside the swing arm, the axle diameter and the brake drum...
Thanks for the hints. I was able to find a new rubber carb connector. That may help since the one that is on there is all checked. I have covered it with hi...
i had a it 465 and parts for sale in previous ads and i finally sold it. unfortunantly it was considerably for far less than what i was trying to get for it...
I recently acquired a 1979 175 IT with only a thousand miles on it. I believe the letters E,F and G refer to the size of the cylinder bore. How do I find out...
I thought the same thing. It was a bit tight, no free play at all. Adjusted the lever and it's a little better. I need a new cable as well. I figure if I'm...
Joel, Do you think the front end will be a direct swap? Good points about the swingarm and rear tire by the way. I noticed that the braking parts were...
COMPLETE FRONT END WILL DROP STRAIGHT IN,REAR WHEEL CAN STILL USE YOUR
ORIGINAL BRAKE PLATE AND WILL FIT. CHEERS MARK. ... From: EnduroITseries@yahoogroups.com...
Hello I have been offered a complete second-hand DG-exhaustsystem(pipe and silencer). What is a fair price for the system without paying too much? Thanks ...
NICE!!!!!!! I will be checking with the yard this week and making them an offer on the parts that I need. ... YOUR ... looking ... advantage ... updating ... ...
I really need a rear axle for my 83 it 175.I could use one off of either 82 or 83 only.Please help me out I am so ready to ride this bike now.Thanks Brad...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
