Jack, ... I think I have one, at least it's an alternator without fan blades and it's quite compact. I have to check if I find it back and check how much it...
axe Loc-tite makes a thread sealer for plumbing joints which seals very well, can be had at Mc Master Carr they are on line. Duff ... From: axe969 To:...
A friend of mine was offered a Indian one cylinder engine from'15, complet and supposted to be in very good condition. What would be a reasonable price for...
Oh I guess I'd take $50 to remove it ... From: Andreas Juerging To: VirtualIndian@yahoogroups.com Sent: Thursday, September 01, 2005 7:49 PM Subject:...
This is probably impractical for those of you on the pricey side of the pond, but WWW.Alterstart.Com has all kinds of alternators and starters for everything....
Herb Meister
Herbiedoo@...
Sep 1, 2005 11:26 am
84330
Ray. Don`t get too involved with the alternator output at present as the alternator is not going to push a higher amperage through a circuit breaker unless...
Ray, Poor grounding should not trip the breaker. Easiest way to trouble shoot is to disconnect the additions/replacements and then reconnect one at a time...
... RAy,no,poor ground would reduce amps and have dim bulb.Lots of good info in Andrews reply. With motor off,turn on everything to get an idea of load from...
Hi Dennis : You can get the bushings out pretty easily by using a long tapered sharp punch and collapsing them into themselves and just pulling them out . Just...
Ok, guys. On my latest 18" rim that I am lacing, I cannot get it any truer than .035" up and down and a little less side to side. When looking at the dial...
Thanks to John, Duff and Michael. As it turns out I may just have been too hasty. A little more aggressive probing showed that what I was feeling was a firm...
Their website has been down for about 3 days. I thyink they are located in Texas but don't knwo where their server is. Figured it was something to do with the...
I thought they were located in delta area? (Baton Rouge??) Jack ... From: Lyle To: VirtualIndian@yahoogroups.com Sent: Thursday, September 01, 2005 7:21 PM ...
Eddie, I think I am pretty close to the limit on the breaker, the ammeter is showing around 18 amps discharge at idle. Will do the calculation per your link,...
Maybe, I've only met him once and that was in Florida at the swapmeet near Daytona. But I thought they had something to do with Texas. maybe that's where the...
i thot flathead power was headquartered in Europe???? Denmark??? Or am i way off base again?? [Non-text portions of this message have been removed]...
Packard56V8@...
Sep 1, 2005 6:10 pm
84343
Lyle I am not a mechanic eather but I watched it once long ago and the first thing they did was check the rim as they some times need a little body and fender...
They started out in Sweden. But then they moved to (Texas - I thought, Jack thinks Louisiana) the USA a couple of years ago. I spoke with Anders back when they...
In a message dated 9/1/05 1:27:32 PM Central Daylight Time, creepinogie@... writes: Supposedly they moved because of manufacturing concerns. But then,...
I think Jack meant that Anders is down in Louisiana IIRC, and subject to the hurricane, and the flatheadpower website has been down... -Guy- ... From:...
Yeah, The days of stuffing sand into various coreboxes and then assemblying the pieces to make a mold (Ander's ULH cyls uses an 8 piece corebox) is coming to...
In a message dated 9/1/05 1:49:28 PM Central Daylight Time, guyiii@... writes: My Chief cylinder from FHP is good. Yep, never had any bad Chief cyls from...
In a message dated 9/1/05 2:03:36 PM Central Daylight Time, creepinogie@... writes: coming to an end with V process, Lost foam, etc. I can't get the...
I contacted a steel foundry in the Mpls area about doing some investment casting work (lost wax) for me and they told me they would think about it for 1000...
In a message dated 9/1/2005 1:48:56 PM Central Standard Time, guyiii@... ... what is IIRC??? [Non-text portions of this message have been removed]...
Packard56V8@...
Sep 1, 2005 8:46 pm
84353
In a message dated 9/1/2005 1:59:54 PM Central Standard Time, ... as far as the FINISHED product is concerened is the "V" procees better than the sand...
