Duff, ok, this time I will mark the message, put it in a special folder, and print it before asking again the question in 1 year... no, I'll ride before :o) --...
John, ... Could you give me the diameters (OD and ID) ? I found a Thrust washer in my micelaneous parts box which would fit the ID but its OD is only 1" 1/4. ...
You mite get better results posing radiator cap questions to www.AACA.org web site. Look at the left side of screen for "Forums". [Non-text portions of this...
Packard56V8@...
May 1, 2005 10:55 am
81459
Michael The email doesn't give me your email I'm at dixchief@... What's up? ... From: VirtualIndian@yahoogroups.com ...
Fred, The washer OD is just under 1-3/8" (actual size = 1.372"). ID is just over 7/8" (.882".) John ... [Non-text portions of this message have been removed]...
there is a site called radiator mascots if this is like a sculpture ypu may be able to find it there bri [Non-text portions of this message have been removed]...
fred, kevin flanagin sells the springs and he may have the washers to fit but as i remember you have to surface grind them to the correct spects ,15 thousanths...
G'day everyone. Does anyone know of a supplier of the? Bakelite (or plastic) wiring blocks that mount into the cut-out on the rear base of the 47 Motolamp...
Listers... I have successfully added a pic of this cap at http://photos.groups.yahoo.com/group/VirtualIndian.list Would appreciate any info that can be...
Hi I am running 500x16 Avon S-M MK11 tires on my 46 Chief. Is 26 pounds about right? I can't see where it says on the tire what pressures to run. I know I...
John and listers, ... the complete correct url is (on 1 line) : http://photos.groups.yahoo.com/group/virtualindian/vwp?.dir=/&.dnm=Radiator+Cap.jpg shortered...
Rod Too much air pressure will cause the rear end to bounce motorcycle wise I mean! Since you are running a much newer tire than the original which would have...
Terry Duffy
MICHIGANDER@...
May 2, 2005 8:56 am
81471
i have some old indian hartley excelsior titles new york call walt off line [Non-text portions of this message have been removed]...
supercyc1@...
May 2, 2005 10:46 am
81472
In a message dated 5/1/2005 2:15:35 PM Central Standard Time, ... THERE IS a cork seal!!! It IS a panhead push rod cover cork. It fits in the recess on the...
Packard56V8@...
May 2, 2005 11:31 am
81473
In a message dated 5/1/2005 2:15:35 PM Central Standard Time, ... What is the washer in the top right corner????? [Non-text portions of this message have been...
Packard56V8@...
May 2, 2005 11:34 am
81474
... in ... yes please. ... it's the beveled washer, the other side is on the middle row, left column. btw, I now see where the cork washer goes... I may have...
Is it an upper or a lower cork? They are different diameters. In any event it should not be needed with the driveshaft seal installed. John ... [Non-text...
In a message dated 5/2/2005 7:18:43 AM Central Standard Time, ... I do not remeber if its an upper or lower panhead seal. I think it is the smaller of the...
Packard56V8@...
May 2, 2005 1:32 pm
81478
The message is ready to be sent with the following file or link attachments: Picture 113 Note: To protect against computer viruses, e-mail programs may prevent...
... the ... John, Bri, Keith and Duff, thanks to you all. Unhappily I was not sure to go to the garage before next week but now it's sure even worst : I just...
John Faylo , This looks like the " Quail " type rad cap so loved by the Model A Ford people. Regards , Chris James. [Non-text portions of this message have...
Christopher James
flatearthspares@...
May 2, 2005 3:16 pm
81481
hi all, just wanted to thank all those who responded to my question on vintage insurance carriers. my question this time is about the attachment of dissimilar...
Hi Rod I have the pressure guide from the old avon website for the SM tyre, It is not a PSI number however but an illustration of how the tyre should look when...
Hi Dave It looks right and rides good so I think I will stay at the 26 pounds for now. it sure is a pleasure to ride with the foot shift and hand clutch. I can...
Rod, Can you post a pic or two of your foot shift setup? If I remember correctly you were going to use a HD mousetrap booster? John ... [Non-text portions of...
