Larry, ... there is a lot of picture of my Chief on my website (www.dufrene.net/indian/en/ => restoration / my chief) but (i've just taken a look) there is...
No need to reply. test only 8.20 p.m. eddie __________________________________ Do you Yahoo!? Free Pop-Up Blocker - Get it now http://companion.yahoo.com/...
... When you`re done Rod, put a little 290 Loctite on the nipples from the well side of the rim, opposite where the spoke enters. It will help reduce...
Gary. Not seen any juice brakes on Indians here in Aus. Local 741 set up with twin leading shoe, but strangely on the rear. My preference would be the front...
I`m getting `em o.k. Fred, eventually. Always used to get my posts a few seconds after hitting the send button. Now it`s hours. And out of sequence. Got a...
hi Eddie, ... It arrive to me time to time too. ... Read the details of the last bounced message, it can expalin you what was the problem. 8 time on 10 it's...
Good Morning Listers: Is it customary to replace the rear plunger bushings when doing a restoration ? I'm not sure what type of fit I'm supposed to have with...
hdcruiser@...
Dec 1, 2003 12:47 pm
67996
RF, Where in the circuit is the fuse located? What is the fuse rating? This is a common symptom if it is in either battery wire at the battery. If the fuse...
Hi all, Had an interesting conversation with my friend Maximillian in Havanna,Cuba today.He tells me that when President Castro took control of Cuba he also...
I hope it wasen't one of those aluminum coffin tank Maicos. Been looking for a cheap one for years... Lyle PS Oops, reread it, 1957 is too early. ... set up ...
It's be a deal to hook up disks on the rear with the speedo drive on the same side as the disk. I've givin it a little thought but I'm sure others have done...
So far I've been lucky in this area. All the sets that I've gone through have been OK. There was a sloppy set, but I had some spares that were in good order....
John, My fuse is on the positive battery lead. The ampmeter show peak charging, even with all the lights on (they then eventually burst until the fuse does...
I'm replacing my tires and since the wheels will be off the bike, I would like to check the trueness(?) of the wheels. My bike has had quite a few things wrong...
Gerald You can make a set up a stand between to chairs with the backs turned toward each other, support your rims between the backs, use a pencil taped to...
Patrica Duffy
MICHIGANDER@...
Dec 1, 2003 3:04 pm
68005
I just roll the wheels in the frame. The forks make the best fixture to hold the wheels. You can tape on indicators, or get fancy with a magnetic based dial...
Hi On my 46 Chief I took off the front fender and used dial indicators with brackets I made bolted to the fender mounting holes. That way I used the whole axle...
Forgot to ad, It would be easier with tires off for checking run out. But you could check first hopefully you are in good shape now. Rod ... From: Rod To:...
Hi Bob I am going to run the stock set up. I read one time that they make a good passing gear. The guy said that when you put them on it seemed to go faster. I...
Yea He did it backwards the first time. He had a ton of money in the paint job and it was perfect. Back to square one now. Rod ... From: Bob Burton To:...
Thanks Eddie Rod ... From: andrew edwards To: VirtualIndian@yahoogroups.com Sent: Monday, December 01, 2003 5:24 AM Subject: Re: [Virtual Indian] bouncing...
Thanks everyone for the opinions on truing. I'm going to check these either on the bike or between 2 chairs as mentioned and if its close, I'm going to live...
Rod, Just out of curiosity, how close did you get your wheels with the dial indicator? I'm using import Indian 18" rims and they are "close" but there is some...
In a message dated 12/1/2003 3:29:58 AM Eastern Standard Time, listes@... writes: there is not pictures of the brake setup,at least close ones. I will ...
Hi Lyle I asked down at my local HD custom shop how close they keep their wheels. They said some wheels the manufacturers call for within .030 ( plus or minus...
Hi All : I know I'm probably gettin' in late on this broken center stand frame tab repair thread -- but I just got done doing the repair (as Mike Breeding told...
