Roy Not asking for any secrets but briefly how do you do this? N...
nowbjr@...
Dec 1, 2008 1:16 pm
110628
You bore the old cylinder out to fit the new sleeve with a -.005 fit ... From: nowbjr@... To: VirtualIndian@yahoogroups.com Cc: roy davies Sent: Monday,...
I need someone with a good memory to recall who or what is the company who can solve the problem below.. I was looking for the thread on cylinder repair... I'm...
Hi Robbie: It sounds like you may not have been receiving the replies to your first inquiry on this question. There have been several. They should be in the...
Robbie it was US Chrome at www.usnicom.com , it was from my questions about sleeving a jug May 2007, Dirtbag ... [Non-text portions of this message have been...
Bill Rowe-Riverview P...
toolroom@...
Dec 1, 2008 8:33 pm
110632
Nikasil, There is an out fit in just about every state that does this process, I have one close to me in Pernnasylvania if interested. Rocky 1957S/VG ... From:...
not lean, retarded. sounds like the owner ... From: Fred Johansen To: virtualindian@yahoogroups.com Sent: Sunday, November 30, 2008 8:36 PM Subject: RE:...
Robbie, Been looking in to the same thing recently. I have not spoken to U.S. Chrome but Powerseal in Pennsylvania can only Nikasil back to the same size...
Robbie, IF you can open get the bore built up, and is a straight threw bore ( no Pocket Cylinders ) you can have them wire burned back to a tenth of a...
US chrome can do the job But if your in the Los Angeles area I can sleeve them for you .- phil ... From: FasstJim@... To: VirtualIndian@yahoogroups.com ...
Yesterdays have one on display / for sale. Won't see that too often ? Nothing to do with me, etc... ...
RohanB
newboltz@...
Dec 2, 2008 9:12 pm
110638
hi , does anyone know where to get the krank vent in Canada ??? or some one who will ship one to Canada ??? , for use on a 84" motor , this is my first...
Old Iron Designs sold & passed on thier wares, including the Indian Chief version of Krank Vent, to Jerry Greers in S. D. They ship anywhere. RF. To:...
Hi Rob No problem I have them on hand, they come with a life time warrenty if the valve wears out or ever needs repaired I will do so free of charge which...
Bob, If you have any questions regarding your 84" engine along the way please feel free to email me off line. We've built quite a few of them and continue to...
Mike Tomas
bigchief@...
Dec 3, 2008 4:55 am
110643
Listers - On my '47 Chief, when I hand-tighten my control sleeve nuts, the control sleeves bind up. If I back the nuts off just a tiny bit, the binding goes...
I've tried several different solutions. Standard disc with hole, motovalve (1st version), krankvent(probably before most of you), open system and kiwi's...
Tom, I think I would take a little off the face of the sleeve on a lathe.This is where you usually need to add shim to tighten up clearance,or take some off...
I had a sleeve that did the same thing, and I did what Tom recommended. I tool a little off with a lathe. Mike ... From: VirtualIndian@yahoogroups.com...
What a remarkable site. That Hendee has a sidecar with it that holds newer batteries and runs the original electric start. The machine is in incredibly good...
Have used the moto valve and Kiwi's vent successfully on my '46 74 inch. Never had any problems what so ever with either one. I also run an external oil filter...
Listers, Does anybody out there have a cam case cover for a '34 Chief that has the hole the cam goes through to operate the points in the pillbox setup that...
Try Randy Zorn of the Big Sandbar Chapter. He had two 34 Chiefs at Jefferson this year. One was his and the other was for Steve Ciccalone. Good luck, Wayne ...
While you are at it check that the spiral is allowing the throttle to fully open. Some repro spirals on the market are only allowing the throttle to have about...
Mike Tomas
bigchief@...
Dec 4, 2008 5:17 am
110653
Testing _________________________________________________________________ Send e-mail faster without improving your typing skills. ...
hi alan things are quiet but you got through ok barry ... From: Alan Hatch To: virtualindian@yahoogroups.com Sent: Saturday, December 06, 2008 6:56 AM Subject:...
Since its quite around here, maybe I can ask a question. On an warly 29 and later Indian Four, there is a cleveis lock nut at the rear end on the clutch...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
